Gorilla Playsets Big Skye I Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 124

background image

2 X 6 X 90"

ROPE LADDER SUPPORT

OFFSET HOLES DOWN

2 X 4 X 58"

BOTTOM PANEL

BOARD

OFFSET HOLES

DOWN

2 X 4 X 90"

ROPE LADDER RUNNER

OFFSET HOLES DOWN

5/16" WASHER

5/16 X 4-1/2"

HEX BOLT

STEP 7: FRAMING THE FRONT OF THE FORT

1: LAY THE 2 X 4 X 90" ROPE LADDER RUNNER AT THE FRONT OF THE FORT AT THE BOTTOM OF THE CORNER POSTS.

THE OFFSET HOLES IN THE ROPE LADDER RUNNER MUST FACE DOWNWARD.
2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE HOLES OF THE ROPE LADDER RUNNER TO THE T-

NUTS INSTALLED ON THE CORNER POSTS.
3: LAY THE 2 X 4 X 58" BOTTOM PANEL BOARD ON THE FRONT CORNER POSTS IN THE MIDDLE OF THE CORNER POSTS.

THE OFFSET HOLES IN THE BOTTOM PANEL BOARD MUST FACE DOWNWARD.
4: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE HOLES OF THE BOTTOM PANEL BOARD TO THE T-

NUTS INSTALLED ON THE CORNER POSTS.
5: LAY THE 2 X 6 X 90" ROPE LADDER SUPPORT ON THE FRONT CORNER POSTS.
6: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE BOTTOM HOLES OF THE ROPE LADDER SUPPORT

TO THE T-NUTS INSTALLED ON THE CORNER POSTS.
7: DO NOT INSTALL LAG SCREWS AT THIS TIME.

43

«
...
41
42
43
44
45
...
»

Содержание Big Skye I





























































































































Отзывы:

Нет отзывов

Похожие инструкции для Big Skye I

Бренд: Kane Страницы: 16

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ODA Страницы: 103

Web Riderz MM00124 Web Swing

Бренд: M&M Sales Enterprises Страницы: 2

Бренд: Malekko Страницы: 2

Бренд: Major Страницы: 26

Бренд: Landoll Страницы: 38

Бренд: Parker Research Corp Страницы: 3

Бренд: schmersal Страницы: 20

Бренд: KaVo Страницы: 70

ROLLING HILLS GS-RH105

Бренд: GSWeb Playground Equipment Страницы: 20

Бренд: EASYFIX Страницы: 16

Бренд: Pamex Страницы: 10

MOVE WASH LIGHT 7

Бренд: N-Gear Страницы: 50

Бренд: Aeroflex Страницы: 60

Бренд: Major tech Страницы: 4

Бренд: VAREM Страницы: 10

Бренд: phase II+ Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды