Gorilla Playsets Big Skye I Скачать руководство пользователя страница 107

Страница: 107 / 124

SAFETY HANDLE

1-1/4" PAN HEAD SCREW

WASHER

ROCK WALL

LADDER

CORNER POST

LOWER LEVEL

FRONT CENTER POST

SWING BEAM

UPPER LEVEL DECK

LAG POST

UPPER LEVEL

FRONT CENTER

POST

(ALTERNATE

PLACE TO MOUNT

SAFETY HANDLES)

STEP 71: SAFETY HANDLES

1: POSITION THE FIRST SET OF SAFETY HANDLES AT THE FRONT OF THE UNIT, ON THE CORNER POST AND LOWER LEVEL

FRONT CENTER POST.
2: THE HEIGHT OF THE SAFETY HANDLES IS NOT CRUCIAL, BUT SHOULD BE PLACED TO ALLOW PROPER ACCESS TO

THE FORT.
3: FASTEN THE SAFETY HANDLES TO THE FORT WITH TWO 1-1/4" PAN HEAD SCREWS AND WASHERS PROVIDED WITH

THE HANDLES.
4: THE UPPER LEVEL SAFETY HANDLES SHOULD BE PLACED ON EITHER THE LAG POSTS, OR CAN BE PLACED ON THE

UPPER LEVEL FRONT CENTER POST, ONCE AGAIN ALLOWING PROPER ACCESS TO THE UPPER LEVEL, AND FASTENED

WITH TWO 1-1/4" PAN HEAD SCREWS AND WASHERS PER HANDLE.

LOWER LEVEL DECK

INSTALLING UPPER LEVEL SAFETY HANDLES

VIEW FROM REAR OF PLAYSET

INSTALLING LOWER LEVEL SAFETY HANDLES

VIEW FROM FRONT OF PLAYSET

107

Содержание Big Skye I





























































































































Результаты поиска

Содержание Big Skye I

Отзывы:

Похожие инструкции для Big Skye I

Бренды по названию

Популярные бренды

Gorilla Playsets Big Skye I, Инструкция по сборке

Результаты поиска

Содержание Big Skye I

Отзывы:

Похожие инструкции для Big Skye I

Бренды по названию

Популярные бренды