Gorilla Playsets 1500BWF Скачать руководство пользователя страница 154

Страница: 154 / 178

Some playsets have a Ladder, Rock Wall or Ramp here. If any of these items are here then this kit has

extra slats to fill up the sides of this opening.

Some playsets have a Tire Swing Beam

attached here.

For those playsets the panel slat steps

in this manual outline how to arrange

the panel slats around where the Tire

Swing Beam is attached.

Some playsets have a Tube Slide here along with a rear mounted Ladder. If the playset has a Tube

Slide here then this kit does not

have extra slats to fill up the spaces between the existing slats.

REAR OF

FORT

REAR OF

FORT

rear mounted Ladder

Plastic Sunburst

(included with playset

NOT with 1531 kit)

Plastic Sunburst

(included with playset

NOT with 1531 kit)

Содержание 1500BWF



















































































































































































Результаты поиска

Содержание 1500BWF

Отзывы:

Похожие инструкции для 1500BWF

Бренды по названию

Популярные бренды

Gorilla Playsets 1500BWF, Руководство пользователя

Результаты поиска

Содержание 1500BWF

Отзывы:

Похожие инструкции для 1500BWF

Бренды по названию

Популярные бренды