Gorilla Playsets 1500BWF Скачать руководство пользователя страница 74

Страница: 74 / 178

STEP 19B: RAMP ROPE HANDRAILS

1: LOCATE THE RAMP ROPES THAT ARE IDENTICAL IN LENGTH. THEY SHOULD BE APPROXIMATELY

12 TO 13 FEET IN LENGTH. IF YOU HAVE FIVE 13 FOOT ROPES THAT IS FINE, HOWEVER IF TWO ARE

12 FEET THEN USE THEM.
2: TIE A KNOT IN ONE END OF A ROPE WITH THE END HANGING OUT ABOUT 2" FROM THE END

OF THE KNOT. THREAD THE OTHER END OF THE ROPE THROUGH THE OUTSIDE OF THE RAMP SIDE.

NOW THREAD IT THROUGH THE EYE BOLT. NOW THREAD IT THROUGH THE HOLE IN THE ROPE

MOUNT ON THE ROPE LADDER SUPPORT. REPEAT THIS PROCESS FOR THE OTHER ROPE ON THE

OTHER SIDE OF THE RAMP
3: TO MAKE THE ROPE TIGHT PLACE A SCRAP BLOCK AROUND 4" THICK UNDER THE BOTTOM

END OF THE RAMP TO ELEVATE IT. NOW TIE A KNOT IN THE END OF THE ROPES AT THE ROPE

MOUNTS. REMOVE THE 4" SCRAP BLOCK FROM UNDER THE END OF THE RAMP. THE ROPES

SHOULD TIGHTEN AND THE RAMP SHOULD BE ON THE GROUND. IF THE RAMP IS ELEVATED OFF

THE GROUND THEN YOU SHOULD PUT A SMALLER BLOCK UNDER THE END OF THE RAMP AND

THEN RETIE THE ENDS NEAR THE ROPE MOUNTS.
4: IF THERE IS ANY EXTRA LENGTH OF ROPE AT THE ROPE MOUNTS THEN TIE AN ADDITIONAL

KNOT IN THE EXTRA LENGTH IF POSSIBLE.
**SAFETY CHECK** - STAND ON THE END OF THE RAMP AT GROUND LEVEL WITH YOUR WEIGHT

ON THE RAMP. GRAB EACH ROPE AND ATTEMPT TO WRAP THEM AROUND YOUR HAND. IF

EITHER ROPE WRAPS AROUND YOUR HAND THEN IT IS TOO LOOSE, UNTIE THE ROPE AT THE ROPE

MOUNT AND RETIE IT UNTIL IT NO LONGER WRAPS AROUND YOUR HAND.

12 TO 13 FEET IN LENGTH.

RAMP POST

ON THE OUTSIDE OF THE

THE INSIDE OF THE

RAMP SIDE.

THORUGH THE EYE BOLT

SECOND: THREAD FREE

APPROXIMATELY

THE OUTSIDE TO

FREE END FROM

THIRD: ROPE GOES THROUGH THE TOP OF THE ROPE

MOUNT HERE. THEN TIE A KNOT OR KNOTS ON THE

RAMP ROPES

BOTTOM SIDE OF THE ROPE MOUNT.

END OF THE ROPE

FIRST: TIE A KNOT

IN THE END OF THE

ROPE HERE FIRST.

THEN THREAD THE

PLACE SCRAP BLOCK

UNDER END OF RAMP

BEFORE TYING KNOTS AT

THE ROPE MOUNTS.

Содержание 1500BWF



















































































































































































Результаты поиска

Содержание 1500BWF

Отзывы:

Похожие инструкции для 1500BWF

Бренды по названию

Популярные бренды

Gorilla Playsets 1500BWF, Руководство пользователя

Результаты поиска

Содержание 1500BWF

Отзывы:

Похожие инструкции для 1500BWF

Бренды по названию

Популярные бренды