Gorilla Playsets 1500AWCR Скачать руководство пользователя страница 69

Страница: 69 / 136

2 X 6 X 79-1/2"

5/16" WASHER

ROPE LADDER

SUPPORT

(OFFSET HOLES DOWN)

RUNNER

HEX BOLT

5/16" X 4-1/2"

5/16" WASHER

HEX BOLT

5/16" X 4-1/2"

HEX BOLT

5/16" WASHER

5/16" X 4-1/2"

ROPE LADDER

2 X 6 X 79-1/2"

2 X 6 X 47-1/2"

BOTTOM PANEL

BOARD

(OFFSET HOLES DOWN)

STEP 2: ASSEMBLING THE RIGHT SIDE FRAME

TO THE T-NUTS INSTALLED ON THE CORNER POSTS.

FRONT OF FORT

8: DO NOT INSTALL ANY LAG SCREWS AT THIS TIME.

1: LAY THE RIGHT SIDE CORNER POSTS ON THE GROUND IN THEIR PROPER ORIENTATION.

2: LAY THE 2 X 6 X 79-1/2" ROPE LADDER RUNNER ON TOP OF THE RIGHT SIDE CORNER POSTS AT THE BOTTOM OF

THE CORNER POSTS. THE HOLES IN THE ROPE LADDER RUNNER MUST BE OFFSET DOWN.

3: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE ROPE LADDER RUNNER TO

THE T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

4: LAY THE 2 X 6 X 47-1/2" BOTTOM PANEL BOARD ON TOP OF THE RIGHT SIDE CORNER POSTS IN THE MIDDLE OF

THE CORNER POSTS. THE HOLES IN THE BOTTOM PANEL BOARD MUST BE OFFSET DOWN.

5: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE BOTTOM HOLES OF THE BOTTOM PANEL

BOARD TO THE T-NUTS INSTALLED ON THE CORNER POSTS. THE TOP HOLES WILL BE USED LATER.

6: LAY THE 2 X 6 X 79-1/2" ROPE LADDER SUPPORT ON TOP OF THE RIGHT SIDE CORNER POSTS. THE HOLES IN THE

ROPE LADDER SUPPORT MUST BE OFFSET DOWN.

7: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE ROPE LADDER SUPPORT

Содержание 1500AWCR









































































































































Результаты поиска

Содержание 1500AWCR

Отзывы:

Похожие инструкции для 1500AWCR

Бренды по названию

Популярные бренды

Gorilla Playsets 1500AWCR, Руководство пользователя

Результаты поиска

Содержание 1500AWCR

Отзывы:

Похожие инструкции для 1500AWCR

Бренды по названию

Популярные бренды