Gorilla Playsets 1500AWCR Скачать руководство пользователя страница 107

Страница: 107 / 136

DETAIL D

5/16" WASHER

5/16 X 3-1/2" LAG SCREW

ROOF BOARD

DETAIL C

5/16" WASHER

1-1/2" WOOD SCREW

WALL PANEL SUPPORT LEFT

1-1/2" WOOD SCREW

ROOF FINISHER FRONT LEFT

1 X 4 X 29.29"

5/16 X 3-1/2" LAG SCREW

FRONT RIGHT

ROOF FINISHER

1 X 4 X 29.29"

ROOF FINISHER

FRONT LEFT

FLUSH

STEP 37: ROOF FINISHERS FRONT

1: PLACE THE 1 X 4 X 29.29" ROOF FINISHER FRONT LEFT ANGLED END ON TOP OF THE GABLE ASSEMBLY LEFT SIDE.

PLACE THE 1 X 4 X 29.29" ROOF FINISHER FRONT RIGHT ANGLED END ON TOP OF THE GABLE ASSEMBLY RIGHT SIDE.

FIT THE TONGUE END INTO THE GROOVE OF THE ROOF BOARD ABOVE THEM.

2: MAKE SURE THAT BOTH ROOF FINISHERS ENDS ARE FLUSH ON BOTH SIDES OF THE ROOF AND TIGHT TO THE GABLE

ASSEMBLY.

TIP: DO THIS ONLY IF "THE ROOF FINISHERS ARE UNEVEN WITH THE OVERHANG". REMOVE THE ROOF FINISHERS SO

YOU CAN ACCESS THE WOOD SCREWS ATTACHING THE WALL PANEL SUPPORTS. ONCE YOU REMOVED THE WALL

PANEL SUPPORTS ON BOTH SIDES, PROCEED TO LOOSEN UP THE WOOD SCREWS ATTACHING THE GABLE ASSEMBLY

FROM UNDERNEATH THE ROOF. SLIDE THE GABLE ASSEMBLY LEFT OR RIGHT. TEST FIT THE ROOF FINISHERS ON BOTH

SIDES. ONCE THE CORRECT POSITION IS ACCOMPLISHED PROCEED TO RE-ATTACH THE REMOVED PIECES.

3: INSERT 5/16 X 3-1/2" LAG SCREWS AND 5/16" WASHERS INTO THE WALL PANEL SUPPORTS AND GABLE ASSEMBLY

COUNTERSUNK HOLES.

4: FASTEN THE ROOF FINISHER FRONT LEFT AND ROOF FINISHER FRONT RIGHT TO THE ROOF SUPPORTS AND TO THE

WALL PANEL SUPPORTS WITH #8 X 1-1/2" WOOD SCREWS ON BOTH SIDES OF THE ROOF.

Содержание 1500AWCR









































































































































Результаты поиска

Содержание 1500AWCR

Отзывы:

Похожие инструкции для 1500AWCR

Бренды по названию

Популярные бренды

Gorilla Playsets 1500AWCR, Руководство пользователя

Результаты поиска

Содержание 1500AWCR

Отзывы:

Похожие инструкции для 1500AWCR

Бренды по названию

Популярные бренды