Gorilla Playsets 1500AWCR Скачать руководство пользователя страница 114

Страница: 114 / 136

STEP 44: PICNIC TABLE

1: MEASURE UP 26-3/8" FROM THE BOTTOM OF THE CORNER POSTS ON THE RIGHT SIDE OF THE PLAYSET. MAKE

MARKS ON THE INSIDE OF THE CORNER POSTS WITH A PEN OR PENCIL AT 26-3/8".

2: PLACE THE TOP OF THE RIGHT SIDE ASSEMBLY FLUSH TO THE MARK ON THE RIGHT FRONT CORNER POST. ATTACH

THE RIGHT SIDE ASSEMBLY TO THE INSIDE OF THE CORNER POST WITH #8 X 3" WOOD SCREWS.

3: PLACE THE TOP OF THE LEFT SIDE ASSEMBLY FLUSH TO THE MARK ON THE RIGHT REAR CORNER POST. ATTACH THE

LEFT SIDE ASSEMBLY TO THE INSIDE OF THE CORNER POST WITH #8 X 3" WOOD SCREWS.

(LEG ON INSIDE)

LEFT SIDE ASSEMBLY

(LEG ON INSIDE)

RIGHT SIDE ASSEMBLY

#8 X 3"

WOOD SCREW

NOTE: ROCK WALL AND LADDER

REMOVED FOR CLARITY.

26-3/8"

Содержание 1500AWCR









































































































































Результаты поиска

Содержание 1500AWCR

Отзывы:

Похожие инструкции для 1500AWCR

Бренды по названию

Популярные бренды

Gorilla Playsets 1500AWCR, Руководство пользователя

Результаты поиска

Содержание 1500AWCR

Отзывы:

Похожие инструкции для 1500AWCR

Бренды по названию

Популярные бренды