2.
Speed Control Adjustment:
The 10 position Speed Control adjustment switch allows the operator to adjust the
speed of the lifting device with a small flathead screwdriver.
3.
Power Up Diagnostic Mode:
When the “E-stop” button is released and power is applied to the lift, the servo
motor controller goes into a power up diagnostic mode test. The following are the sections of the diagnostic
mode test:
a) LED Indicator Test:
The purpose of this test is to verify the five (5) indicator LEDs are functional.
When the E-stop button is released, the yellow “Power On” LED comes on immediately indicating the
internal 24 volt power is operational. After the servo controller completes a series of self-tests, it turns
on the four (4) remaining LEDs for two (2) seconds to simply verify functionality.
b) Switch Test:
After completion of the indicator test, a system switch test is started. The purpose of this
test is to display the state of the “Slack” switches and “Upper and Lower Limit” switches. During the
switch test, the Green “Standard Mode” LED will remain on if the “Upper Limit” switch is triggered (up
limit state) and the Blue “Float Mode” LED will remain on if the “Slack” switches are triggered (wire rope
slack). Once the operator present switch or jog switch is activated, the servo motor controller exits the
power up diagnostic mode and goes into normal operation.
Note:
The Yellow Power On indicator will remain on during the power up diagnostic mode test.
4.
Power On LED (Yellow):
The “Power On” LED illuminates when the required 220 VAC, single-phase power
has been correctly applied to the system and the E-Stop button has been released.
5.
Standard Mode LED (Green):
The “Standard Mode” LED illuminates when all system initialization is complete
and the operator present switch is depressed, thus activating the standard mode of operation.
6.
Capacity Overload LED (Orange):
The “Capacity Overload” LED illuminates when a load or impact load
greater than the capacity of the hoist has been detected by the system. When this LED illuminates, the
controller will allow the operator to lower the load, but it will inhibit the operator from raising the load prior to
“resetting” the system. To clear the overload fault and “reset” the system, release the switch for approximately 1
to 2 seconds. Once the LED turns off, the system can again be operated.
7.
Float Mode LED (Blue):
If the unit is equipped with Float Mode (system option), the “Float Mode” enabled LED
will illuminate when the Float Mode button is pressed on the hand controller and Float Mode has been initiated.
8.
System Fault LED (Red):
The “System Fault” LED flashes when basic faults have been detected by the control
system. If a fault has occurred, the “Standard Mode” or “Float Mode” (if equipped) LEDs will turn off.
9
4/04-Rev. S
®
Содержание 150 BX G-Force
