Goodyear GY 33SBC, Руководство пользователя

Страница: 11 / 88

English Operating manual
11
Dis pos al ins tructions
Dispose of packaging remnants,
old mowers, etc. , in accordance
with local regulations.
Installing and setting the
handle bar
Fig. 2a
Remove the upper retaining plate
from the handle holder.
Push cable harness holder onto
the right control handle.
Insert right control handle into the
lower holder.
Insert left control handle into the
lower holder.
Attach upper retaining plate and
tighten the screws.
Press cable harness into the hol
-
ders.
Installing/removing the lower
drive shaft
Fig. 2b
Assembly
Remove protective cap (optional)
from the shaft coupling and lower
drive shaft.
Turn screw handle (1) on the
shaft coupling (2) anti-clockwise
to open the shaft coupling.
Press release button (3) on the
lower drive shaft and push the
shaft into the shaft coupling until
the release button engages in the
retaining hole (4).
Note
If required, turn the lower drive
shaft slightly until the square shaft
and the holder of the upper drive
shaft mesh.
Tighten screw han dle (1) on the
shaft coupling clockwise. C heck
that the lower drive shaft is tight.
Disassembly
Turn screw handle (1) on the
shaft coupling (2) anti-clockwise
to open the shaft coupling.
Press release button (3) and pull
the lower drive sh aft straight out
of the shaft coupling.
Adjusting the carrying
system (shoulder strap)
Fig. 3
Place harness over your shoul
-
ders.
Close the catch on the abdominal
belt (1.). If required, readjust.
Adjust abdominal belt to the cor
-
rect width (2.).
Adjust shoulder belt to the cor
-
rect length (3.).
Latch the hook of the carrying sy
-
stem into the holder on the unit
(4.) and adjust the attachment
pad to a comforta ble length (5.).
Note
Clip A is used in an emergency to
release the appliance as quickly as
possible from the carrying system.
To do this, pull the clip upwards.
Attaching the cutting
attachment cover
Fig. 4
Unscrew the screws (1) and re
-
move the clamp (2) from the cut
-
ting attachment cover (3).
Place cutting attachment cover
(3) on the lower drive shaft (4)
and attach the clamp (2) with the
screws (1). Do not tighten the
screws yet!
Remove screw (5) from the gear
-
box.
Attach holder (6) to the gearbox
with the screw (5).
Tighten the screws (1).
Attaching/removing the line
head
Attaching the line head
Fig. 5
If attached, remove cutters and
blade attachment parts before -
hand. See “Removing the cutting
blade”.
Push spacer (1) onto the drive
shaft (2).
Align the 3 openings in the
spacer (3), the gearbox (4) and
the gear cover (5).
Note
If alignment is not correct, the line
head cannot be attached/removed!
Insert retaining bar (6) through
the openings (3, 4, 5) in order to
secure the gearbox.
While holding the retaining bar
(6), turn the line head (7) anti-
clockwise (to the left) onto the
drive shaft. Tighten line head
firmly!
Note
Ensure that the line head (7) is sea
-
ted correctly on the spacer (1), i.e.
centred and resting flat!
Remove retaining bar from the
gear head.
R emove the line head
Fig. 6
Align the openings (3, 4, 5). In
-
sert retaining bar (6) through the
openings and hold in position.
Unscrew line head (7) clockwise
(to the right) off the drive shaft.
Attaching/removing the
cutting blade (depending on
model)
Attaching the cutting blade
Fig. 7
If attached, remove the line head
beforehand. See “Attaching/re -
moving the line head”.
Note
When attaching the cutting blade
for the first time, remove the blade
attachment parts (blade holder (8),
retaining bell (9), nut (10)) if atta -
ched. See “Removing the cutting
blade”.
Push spacer (1) onto the drive
shaft (2).
Align the 3 openings in the
spacer (3), the gearbox (4) and
the gear cover (5) (Fig. 5).
Note
If alignment is not correct, the cut
-
ting blade cannot be attached/
removed!
Insert retaining bar (6) through
the openings (3, 4, 5) in order to
secure the gearbox.