background image

06

35

GOODNATURE X-6 COMMERCIAL COLD PRESS JUICER

OWNER’S MANUAL

Section 1: 

Safety Precautions

WARNING: Operator shall not interfere with interlock device.

CAUTION: Safety glasses must be worn at all times during operation of the EG-260 Grinder. Machine can be 

run at a very high speed; splatter and projectiles causing eye damage and irritation is possible.

WARNING: Operator should ensure the surrounding area is free of debris and slipping hazards to 

prevent injury.

NOTICE: Noise levels exceed 80 decibels.  Protective ear equipment should be worn to prevent injury.

WARNING: In the event of an accident or breakdown, all power supply should be disconnected from source 

and Goodnature customer service should be contacted for support.

WARNING: Operator should not use unauthorized means of gaining access to parts of the machine which are 

not normally accessible.

CAUTION: Blades on the grinder disc are very sharp. Use caution when changing the disc to avoid personal 

injury including lacerations.

WARNING: Operator should ensure plug is visible from points of access.

NOTICE: The X-6 Press is only to be used in conjunction with the EG-260 Grinder. Do not mount any other 

equipment to the X-6 Press.

NOTICE: Relieve pressure from hydraulic system by cycling the directional control lever prior to servicing.

Содержание EG-260 Grinder



































Отзывы: