Goblin 380 KYLE STACY EDITION Скачать руководство пользователя

Страница: 36 / 39

Tail Spindle

[H0510-S]

- 1 x Tail Spindle.

- 1 x Socket Cap Screw M2x6mm.

- 2 x Washer 2x 4.5x0.5mm.

Tail Blade Grip

[H0511-S]

- 2 x Tail Blade Grip.

- 2 x Thrust Bearing 3x 6x2.5mm.

- 2 x Bearing 3x 7x3mm.

- 2 x Bearing 3x 6x2.5mm.

- 2 x Washer 3x 4.75x0.5mm.

- 2 x Washer 4.5x 5.9x0.5mm.

- 2 x Washer 2x 4.5x0.5mm.

- 2 x Uniball M3.

Tail Pitch Slider

[H0512-S]

- 1 x Tail Pitch Slider 01.

- 1 x Tail Pitch Slider 02.

- 1 x Tail Pitch Slider 03.

- 2 x Flanged Bearings

8x 12x3.5mm.

Main Blade Grip

[H0513-S]

- 2 x Blade Grip.

- 2 x

Thrust Bearing 5x 10x4.

- 4 x

Bearing 5x 10x4.

- 2 x Washer 7.5x 10x0.5.

- 2 x Button Head Socket Cap M4x6.

- 2 x

Washer 5x 7x0.1.

Center Hub

[H0514-S]

- 1 x Center Hub.

- 1 x Socket Head Shoulder M3x16

- 1 x Metrix Hex Nylon Nut M3

Blade Grip Arm

[H0517-S]

- 2 x Blade Grip Arm.

- 2 x Head Cap Screws M2.5x8.

- 2 x Uniball M2.

Main Plate

[H0519-S]

- 1 x Main Plate.

- 1 x Bearing 8x 16x5.

Motor Support

[H0520-S]

- 1 x Motor Support.

- 3 x Head Cap Screws M2.5x8.

- 3 x Finishing Washer M2.5.

- 1 x Set Screws M4x12.

- 1 x Metrix Hex Nylon Nut M4.

- 1 x Washer 4x 11x1mm.

Main Shaft Support

[H0522-S]

- 1 x Main Shaft Support.

- 3 x Head Cap Screws M2.5x8.

- 1 x Bearing 8x 16x5.

Aluminum Tail Plate

[H0523-S]

- 1 x Aluminum Tail Plate.

- 1 x Flanged Bearing

5x 13x4.

- 2 x Head Cap Screws M2.5x10.

- 2 x Finishing Washer M3.

Linkage Servo

[H0524-S]

- 3 x Aluminum Tail Plate.

Cros Tail Case

[H0526-S]

- 1 x Cros Tail Case.

- 2 x Head Cap Screw M2.5x6.

Plastic Landing Gear

[H0528-S]

- 1 x Plastic Landing Gear.

- 2 x Head Cap Screw M2.5x8.

- 2 x Finishing Washer M2.5.

Plastic Battery Support

[H0529-S]

- 1 x Plastic Battery Support.

Tail Servo Support

[H0530-S]

- 1 x Tail Servo Support.

- 4 x Buttom Head Cap

Specail M2.5x6.

- 2 x Uniball M2 Female.

Uniball M2 Female

(H0537-S)

Battery Tray

(H0536-S)

- 1 x M8 Carbon Block.

- 2 x Locking Element Tail.

- 1 x Double Sided Tape [HA034].

- 1 x Double Sided Tape [HA033].

- 1 x Metrix Hex Nylon Nut M8.

- 1 x Metrix Hex Nylon Screw M8.

- 4 x Metrix Hex Nylon Nut M2.5.

Boom Accessories

(H0535-S)

- 1 x Anti-Rotation Guide.

- 2 x Head Cap Screws M2.5x6.

Anti-Rotation Guide

(H0533-S)

Vertical Fin

(H0532-S)

- 1 x Vertical Fin.

- 2 x Finishing Washer M3.

- 2 x Head Cap Screws M2.5x6.

- 2 x Head Cap Screws M2.5x10.

- 1 x Main Frame.

Main Frame

(H0531-S)

- 1 x Battery Tray.

- 1 x Battery Straps.

- 1 x Double Sided Tape [HA036].

Chapter 19, Spare Parts

Page 34

Содержание 380 KYLE STACY EDITION








































Результаты поиска

Содержание 380 KYLE STACY EDITION

Отзывы:

Похожие инструкции для 380 KYLE STACY EDITION

Бренды по названию

Популярные бренды

Goblin 380 KYLE STACY EDITION, Руководство пользователя

Результаты поиска

Содержание 380 KYLE STACY EDITION

Отзывы:

Похожие инструкции для 380 KYLE STACY EDITION

Бренды по названию

Популярные бренды