Goblin 380 KYLE STACY EDITION Скачать руководство пользователя

Страница: 35 / 39

- 5 x Uniballs M2 5H6.

- 5 x Uniball Spacers.

- 5 x Socket Head Cap Screws

M2x8mm.

- 5 x Socket Head Cap Screws

M2x6mm.

Uniball M2 5H6

[H0064-S]

- 5 x Uniballs M3x4 5H3.5.

Uniball M3x4 5H3

[H0065-S]

- 10 x Plastic Ball Link.

Plastic Ball Link

[H0066-S]

Bell Crank Lever

[H0234-S]

- 1 x Bell Crank level.

- 2 x Tail Pin.

- 2 x Flanged Bearing

2.5x 6x2.5mm.

- 1 x Spacer Arm 2.5x 4x6.3.

- 1 x Head Cap Screws M2.5x18.

- 1 x Uniball M3x 4 H5.

Finishing Washer M2.5

[H0255-S]

- 10 x Finishing Washer M2.5.

Tail Pitch Slider Link

[H0261-S]

- 2 x Tail Pitch Slider Link.

- 2 x Spacer 2x 3x3mm.

- 2 x Socket Head Cap M2x6mm.

Plastic Ball Link M2

[H0403-S]

- 5 x Plastic Ball Link M2.

19T Motor Pulley

[H0501-19-S]

- 1 x 19T Motor Pulley Assembly.

- 1 x Set Screws M3x6mm.

- 1 x 20T Motor Pulley Assembly.

- 1 x Set Screws M3x6mm.

20T Motor Pulley

[H0501-20-S]

21T Motor Pulley

[H0501-21-S]

22T Motor Pulley

[H0501-22-S]

23T Motor Pulley

[H0501-23-S]

24T Motor Pulley

[H0501-24-S]

- 1 x 21T Motor Pulley Assembly.

- 1 x Set Screws M3x6mm.

- 1 x 22T Motor Pulley Assembly.

- 1 x Set Screws M3x6mm.

- 1 x 23T Motor Pulley Assembly.

- 1 x Set Screws M3x6mm.

- 1 x 24T Motor Pulley Assembly.

- 1 x Set Screws M3x6mm.

- 1 x 120T Main Pulley .

- 1 x Main Pulley Support.

- 2 x Shims Ø8xØ14x0,2mm.

- 5 x Head Cap Screws M2x5mm.

- 2 x Flanged Bearing Ø8xØ12x3,5mm.

- 1 x One Way Bearing Ø8xØ12x12mm.

Front Tail Pulley

[H0503-S]

20T Tail Pulley

[H0504-S]

- 1 x Front Tail Pulley Assembly.

- 1 x Head Cap Screws Shoulder

M2.5x15.

- 3 x Head Cap Screws M2x8mm.

- 1 x 20T Tail Pulley Assembly.

- 1 x Set Screws M3x6mm.

21T Tail Pulley

[H0505-S]

- 1 x 21T Tail Pulley Assembly.

- 1 x Set Screws M3x6mm.

- 1 x Swashplate Assembly.

- 1 x Rad Bearings 25x 32x4.

- 6 x Uniballs M2 Male.

- 1 x Uniballs M2 Female.

- 3 x Button Cap Screws M2x5.

- 3 x Swasher 2.2x 4x0.3.

- 2 x Head Cap Screws M2x8mm.

Main Shaft

[H0507-S]

- 1 x Main Shaft.

- 1 x Head Cap Screw M3x16mm.

- 1 x Metrix Nylon Nut M3.

Washplate Set

[H0506-S]

25T Motor Pulley

[H0501-25-S]

- 1 x 25T Motor Pulley Assembly.

- 1 x Set Screws M3x6mm.

120T Main Pulley

[H0502-S]

- 1 x Tail Shaft.

- 1 x Tail Hub.

- 1 x Set Screw M3x6mm.

- 2 x Tail Damper.

Tail Shaft

[H0509-S]

Chapter 19, Spare Parts

Page 33

Содержание 380 KYLE STACY EDITION








































Результаты поиска

Содержание 380 KYLE STACY EDITION

Отзывы:

Похожие инструкции для 380 KYLE STACY EDITION

Бренды по названию

Популярные бренды

Goblin 380 KYLE STACY EDITION, Руководство пользователя

Результаты поиска

Содержание 380 KYLE STACY EDITION

Отзывы:

Похожие инструкции для 380 KYLE STACY EDITION

Бренды по названию

Популярные бренды