manualshive.com logo in svg

Goblin 380 KYLE STACY EDITION, Руководство пользователя

Поделиться
Скачать
Goblin 380 KYLE STACY EDITION Скачать руководство пользователя страница 9

Button Head Cap Screw 

M3x4mm

......x1

Flat Head Cap Screw  

M2.5x5mm

(HC128-S)

Socket Head Cap Screw 

M3x8mm

Socket Head Cap 

Screw M3x8mm

(HC050-S)

Bearing  12x 24x6mm

......x3

Socket Head Cap 

Screw M3x10mm

(HC056-S)

Column

(H0018-S)

Bearing  10x 19x5mm

Bearing  12x 24x6mm

Flat Head Cap Screw 

M2.5x5mm

Bearing 

10x 19x5mm

(HC422-S)

Note:

Socket Head Cap 

Screw M3x10mm

(HC056-S)

Note:

       You must be put strong main gear 

(H0320-S) before you put 3 column on main 

structure

Bag 2, Bag 19

Main Shaft Support Assembly 

Main Shaft Support

(H0522-S)

Bearing  Ø8xØ16x5mm

(HC419-S)

Main Shaft Support 

Assembly 

Main Shaft

(H0507-S)

Bearing  Ø8xØ16x5mm

(HC419-S)

Socket Head Cap 

Screw M2.5x8mm

(HC020-S)

Socket Head Cap 

Screw M2.5x8mm

(HC020-S)

Main Shaft Assembly 

Main Shaft 

Assembly 

Main Plate

(H0519-S)

Socket Head Cap 

Screw M2.5x8mm

(HC020-S)

Shims Ø8xØ12x0,1mm

(HC462-S)

Note:

Tighten the three screw M2.5. 

After tightening, check the 

axial play of the main shaft. It 

is possible to reduce any axial 

play by adding shims.

IMPORTANT:

 Very carefully 

check to make sure you can 

turn the main shaft freely.

If you feel too much friction, 

you have used too many 

shims, you can remove a shim 

until the shaft turns freely.

Serial Number

[Bag 19]

Page 7

Chapter 5, Transmission Assembly

Содержание 380 KYLE STACY EDITION








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды