background image

gpelectric.com  |  [page 5]

GENERAL INFORMATION

Personal Safety

WARNING!  

Personal Injury

Use safe lifting techniques when lifting this equipment as 

recommended by the Occupational Safety and Health 

Association (OSHA) or other local codes.

Use standard safety equipment when working on this 

equipment, such as safety glasses, ear protection, steel-

toed safety boots, safety hard hats, etc.

Use standard safety practices when working with electrical 

equipment.  (Remove all jewelry, use insulated tools, wear 

cotton clothing, etc.)

Never work alone when installing or servicing this 

equipment.  Have someone nearby that can assist if 

necessary.

Ensure that children, pets, and other animals are kept away 

from the inverter, solar arrays, battery bank, and utility grid 

components.

If the equipment is used in a manner not specified by the 

manufacturer, the protection provided by the equipment may 

be impaired.

People with pacemakers should consult their physician(s) 

before use.  Electromagnetic fields in close proximity to 

heart pacemakers could cause pacemaker interference or 

pacemaker failure.

The brass components of this product contain lead, a 

chemical known to the State of California to cause birth 

defects or other reproductive harm.

This product contains or, when used, produces a chemical 

known to the State of California to cause cancer and birth 

defects or other reproductive harm.

The warnings, precautions, and instructions in this manual 

cannot cover all possible conditions and situations that may 

occur. It must be understood by the operator that common 

sense and caution are factors which cannot be built into this 

product, but must be supplied by the operator.

Содержание GP-1750HD GP































Отзывы: