11 94001 GM-Racing XG-6i Race Spec Instructions
English
14. TH HOLD
This function allows the Throttle Servo to be set to a percentage of the total travel
range. This is an alternative to using the motors choke when starting up the model. Throttle
hold can be performed by pressing the switch to stop the engine. It can be perfor-
med for accident braking. When pressing the switch, throttle trigger doesn‘t work until
the switch is pressed again.
1. Press “ENTER” to see FUNCTION MENU
2. Use the +/- Keys to select the TH HOLD function and press ENTER.
3. Use the +/- Key to change the value.
4. Press EXIT twice to save and return to FUNCTION MENU, press EXIT again
to return to the Main Screen.
TERMS: VALUE -- Throttle hold position. Range: -120% to +120%.
13. MIXER (MIX)
This function allow custom to apply mixing between the steering, throttle, and channel
3 channels.There are main channel and sub-channel in the MIX selection. The servo
travel value of the sub channel is changed along with the change of the main channel
according to the setting rate.
1. Press “ENTER” to see FUNCTION MENU
2. Use the +/- Keys to select the BR_MIX function and press ENTER.
3. Press ENTER to select a item.
4. Firstly main channel setting. Select channel No. (ST, TH, AUX) by “+” or “-“. L and R se-
parately correspond to the rate of Left and Right servos of the main channel mix
5. Secondly sub channel setting. Select channel No. (ST, TH, AUX) by “+” or “-“. L and R
separately correspond to the rate of Left and Right servos selected in the sub
channel.
6. Third Press ENTER to select EN item. Use +/- to select “ON” to enable the
function, and “OFF” to disable the function.
7. Press EXIT twice to save and return to FUNCTION MENU, press EXIT again to
return to the Main Screen.
Exemple:
ST
L 50%
R 30%
If throttle servo is 60% on the right and rudder servo is 50% on the right,
and then after setting, throttle servo is: 50*30%+60%*50%=45%. Thrott-
le servo will act along with the action of STEERING servo.
TH
L 20%
R 50%
EN
„ON“
94001 GM-Racing XG-6i Race Spec Instructions 08
English
ENTER MODEL NAMES:
1. Press “+” or “-”to choose “EDT”.
2. Press “ENTER” to enter rename mode ,Press “+” or “-”to choose “0.1.2....I”
3. Press “ENTER” on the display to save your modifi ed and return to the MODEL Screen..
4. Press “EXIT”to save your setting and leave EDT interface, and back to the function
menu
interface.
COPY ONE MEMORY TO ANOTHER:
1. Press “+” or “-”to choose “CPY”.
2. Press “ENTER” to enter copy mode ,Press “+” or “-”to choose “Mod01....Mod15”
3. Press “ENTER”to save your setting and Press “EXIT”leave CPY interface, and
back to the function menu interface.
8. MODELL MEMORY (MODEL)
Press “ENTER” in the power on interface, and enter function menu interface. Press
“+” or “-“ to choose MDL, and press “ENTER” to enter MODEL adjusting interface.
1. Press “ENTER” to choose “mod00”.(SEL)
2. Press “+” or “-”to choose “mod00~mod15”
3. Press “EXIT”to save your setting and leave SEL interface, and back to the function
menu
interface.
94001-eng.indd Druckbogen 9 von 10 - Seiten (12, 9)
94001-eng.indd Druckbogen 9 von 10 - Seiten (12, 9)
19.01.2009 08:02:49
19.01.2009 08:02:49
