17 94001 GM-Racing XG-6i Race Spec Instructions
English
Konformitätserklärung gemäß dem Gesetz über Funkanlagen und
Telekomunikationsendeinrichtungen (FTEG) und der Richtlinie 1999/5/EG (R&TTE)
Declaration of Conformity in accordiance with the Radio and Telecomunikations Terminal Equipment
Act (FTEG) and Directive 1999/5/EG (R&TTE)
Graupner GmbH & Co. KG
Henriettenstraße 94-96
D-73230 Kirchheim/Teck
erklärt, dass das Produkt:
declares that the product
Geräteklasse:
1
Equipment class
den grundlegenden Anforderungen des § 3 und den übrigen
einschlägigen Bestimmungen des
FTEG (Artikel 3 der R&TTE) entspricht.
complies with the essential requirements of § 3 and the other relevant provisions of the FTEG (Article 3 of the
R&TTE Directive).
Angewendete harmonisierte Normen:
Harmonised standards applied
EN 60950:2006
EN 301 489-1 V1.8.1:2008
EN 301 489-3 V1.4.1:2002
EN 300 440-1 V1.4.1:2008
Health and safety requirements pursuant to § 3 (1) 1. (Article 3 (1) a))
Protection requirement concernig electromagnetic compatibility
§ 3 (1) 2, Artikel 3 (1) b))
Measures for the efficient use of the radio frequency spectrum
§ 3 (2) (Article 3 (2))
Kirchheim, 15. Januar 2009
Hans
Graupner,
Geschäftsführer
Hans Graupner, Managing Director
Graupner GmbH & Co. KG Henriettenstraße 94-96 D-73230 Kirchheim/Teck Germany
Tel: 07021/722-0
EMail: [email protected]
Fax: 07021/722-188
Gesundheit
und Sicherheit gemäß § 3 (1) 1. (Artikel 3 (1)a))
Schutzanforderungen in Bezug auf elektromagnetische
Verträglichkeit § 3 (1) 2, Artikel 3 (1) b))
Maßnahmen zur effizienten Nutzung des Frequenzspektrums
§ 3 (2) (Artikel 3 (2))
Graupner XG-6i
0678
EN 300 440-2 V1.2.1:2008
BINDING PROCESS
1. Press “ENTER” to see FUNCTION MENU
2. Use the +/- Keys to select the MODULATE function and press ENTER.
3. Use the +/- Keys to select YES .
4. Press ENTER to see SETTING…
5. Press EXIT to return to FUNCTION MENU, press EXIT again to return to the Main
Screen.
94001 GM-Racing XG-6i Race Spec Instructions 02
English
THE REMOTE CONTROL SYSTEM
Here you get an overview of the XG-6i Race Spec 2.4 Ghz 3-channel remote control system
and its various functions and settings. Before the fi rst trip should be sure all of these functions
and settings have read and understood.
GETTING STARTED
1. Place 8 AA batteries in the battery compartment in the bottom of the transmitter. Pay
attention to the polarity! If the batteries are loaded incorrectly, the transmitter may be
damaged.
When the transmitter will not be used for a longer period of time, always remove the
batteries.
2. Connect and install the receiver and servos.
Attention:
The transmitter comes with a Futaba charge socket for the use with Charging-Cord
No. 3022.65! Do not use any other Graupner charging cord, this may destroy the bat-
teries.
Be careful with the installation of the receiver. Never bend or shorten the coaxial
antenna wire! The actual „antenna“ is the stripped end of the antenna wire and
must be installed in the vehicle so far above as possible. Avoid damages of the
antenna cable!
Atttention:
Before setting ID Code, Please plug the bind plug into the fi rst channel of the
•
receiver and then turn on the receiver power, The receiver will come into the set ID
Code
mode.
When set ID Code is OK, the “SET OK ” is displayed on the LCD. Otherwise
•
“SET ERR” will be displayed on the LCD.
During Frequency Pin Setup, please gather Tx and Rx as close as possible.
Bind-Plug
94001-eng.indd Druckbogen 3 von 10 - Seiten (18, 3)
94001-eng.indd Druckbogen 3 von 10 - Seiten (18, 3)
19.01.2009 08:02:45
19.01.2009 08:02:45
