Glow-worm 38cxi Скачать руководство пользователя страница 42

Страница: 42 / 47

2000225065A

14.36 Hydroblock Assembly Left-Hand

Refer to section 12.9 to drain the boiler heating circuit.

Refer to section 12.10 and drain the boiler hot water circuit.

Refer to diagram 14.26.

Undo the connector on the bottom of the flow pipe from the
hydroblock.

Undo the nut connecting flow pipe to heat exchanger.

Lift the flow pipe up out of the way.

Remove the filling loop tube, refer to section14.26.

Remove the reduced pressure zone valve, refer to section
14.29.

Remove the bypass tube, refer to section 14.25.

Undo the safety discharge valve union and remove the pipework.

Remove the securing clip and withdraw the safety discharge
valve, refer to section 14.17.

Remove securing clips 1 and 2 below hydroblock, see diagram
14.26.

Undo three securing screws on the underside of the left-hand
hydroblock.

Remove the diverter switch as described in section 14.15.

14 Replacement of Parts

Diagram 14.26

Remove left hand hydroblock from plate-to-plate heat exchanger
using a TORX screwdriver to remove the securing screw, see
diagram 14.26.

Lift out the left hand hydroblock.

Remove the remaining components for refitting into the
replacement left hand hydroblock.

Refill, vent and pressurise the boiler.

Open the cold water isolation valve and slowly open a hot water
tap to remove air. Close the hot water tap.

Check for any leaks.

14.37 Diverter Valve

For access, refer to section 14.1.

Refer to section 12.9 and drain the boiler heating circuit.

Refer to section 12.10 and drain the boiler hot water circuit.

Remove the diverter switch as described in 14.15.

Refer to section 14.36 to remove the left hand hydroblock.

Unscrew and remove both halves of the diverter valve from the
left hand and right hand sides of the hydroblock, see diagram
14.27.

When replacing the two halves of the diverter valve it is
important to ensure the spindle is located correctly. This can be
observed with the left hand hydroblock removed.

SAFETY
DISCHARGE
VALVE

SECURING
CLIP 1

FLOW PIPE
CONNECTOR

PLATE TO PLATE HEAT
EXCHANGER SECURING SCREW

SECURING
CLIP 2

SECURING
CLIP 3

RH
HYDROBLOCK

LH
HYDROBLOCK

OUTLET
CONNECTOR

PLATE TO PLATE HEAT
EXCHANGER SECURING
SCREW

SECURING
CLIP 4

11499

11478

11500

Содержание 38cxi
















































Результаты поиска

Содержание 38cxi

Отзывы:

Похожие инструкции для 38cxi

Бренды по названию

Популярные бренды

Glow-worm 38cxi, Инструкция по использованию, установке и обслуживанию

Результаты поиска

Содержание 38cxi

Отзывы:

Похожие инструкции для 38cxi

Бренды по названию

Популярные бренды