background image

Wall Mounted Water Bottle 

Refilling Station

8

Assembly Instructions

Valve Control

•   Ensure both water control valves are turned to the 

closed position.

•   Attach 2 screws (not included) through the frame 

of the Cooling System and into the bottom support 

holes previously drilled into the wall.

•   Connect  the  building's  water  supply  to  the  Filter 

Head Connection. This connection must be made 

through the back of the Cooling System.

•   Connect  the  internal  drain  line  to  the  building's 

external  drain.  This  connection  must  be  made 

through the back of the Cooling System.

Install water filter 

•   Remove  the  receiver  protective  cover  from  the 

water filter.

•   Insert filter into the filter head by turning clockwise 

until locked into place.

•   Turn both water control valves to the open position.

•   Check  all  connections  for  leaks.  If  leaks  are 

detected ensure all connections are tight and are 

fully inserted.

11

13

12

Closed

Closed

Closed

Open

•  Open the water control valve

labeled “sensing spout”

•  Keep the water control valve

labeled “basin bubble” in the 

closed position.

(CHECK FOR LEAKS)

Water Control Valves

Wall mounting

hardware not  

provided

Water Filter

Counter clockwise to remove

Clockwise to install

Connect filter 

head to water 

supply

9

Note:

 If cooling system is on its side or back 

for more than  10  minutes,  allow  it  to  stand  in 

the  upright position for 24 hours before water 

connections and initial power-on. 

•   Turn on buildings water supply and 

check all connections for leaks.

•   Fix any leaks before continuing.

•   Plug power cord into outlet.

 Check local codes for plumbing requirements 

prior to installation.

b82045fc-0b136962-90871f19-f891407c

Содержание 761219













Отзывы: