background image

7

Assembly Instructions

Wall Mounted Water Bottle 

Refilling Station

Attach mounting brackets to wall

•   Affix stencil with tape to appropriate wall. It is recommended to use a 

level to ensure the stencil is hung straight horizontally.

•   Drill (9) holes appropriate for the wall anchors (75 lb. minimum each) 

as indicated on the top and bottom mounting brackets on the stencil. 

Use appropriate anchors for your wall type.

•   Drill 2 holes appropriate for the wall anchors (75 lb. minimum each) as 

indicated on the bottom support holes on the stencil. Use appropriate 

anchors for your wall type.

•  Remove stencil from the wall and install top and bottom brackets onto 

the wall using appropriate anchors.

Hanging assembled unit to wall

•   Carefully hang assembled bottle filler onto 

the  wall  by  lowering  onto  both  top  and 

bottom wall mount brackets. 

8

9

Note:

 To comply with ADA requirements, the base of stencil must 

be installed 11" to 14

3

/

4

" from the floor. See Rough-in Guide for 

additional ADA requirements.

Note:

 Before installing brackets to the wall, assure power source, 

water line and drain aligns to opening on unit

Attach back plate

Reattach  the  Back  Plate  onto  the

rear of the Bottle Filler Top Assembly

using  the  (3)  screws  previously

removed, plus (6) (H4) screws.

Unit is now ready for mounting.

       CAUTION

Once assembled, do not lift unit by Bottle Filler 

Top  Assembly.  Use  two  people  when  lifting. 

Always wear work gloves when lifting

Lift 

Points

H5

9X

See wall 

mounting 

template

Level

10

b82045fc-0b136962-90871f19-f891407c

Содержание 761219













Отзывы: