background image

 

1

Wall Mounted Water Bottle Refilling Station

070121

User's manual

Manual del usuario

Manuel de l'utilisateur

Customer Service

US: 1-800-645-2986

Servicio de atención al Cliente

US: 1-800-645-2986

Service à la clientèle

Canada: 888-645-2986

         WARNING

  

 Keep  compressor  in  upright  position  for  24  hours 

before water connections and initial power-on. Failure 

to do so will void warranty.

•  For indoor commercial use only.

•   All installation work must be performed by authorized 

service personnel.

•   Two or more people are recommended to lift and install 

the unit.

•   To avoid the risk of property damage and/or personal 

injury, mount the unit to a flat finished wall surface with 

adequate support.

•   Check  local  codes  for  plumbing  requirements  prior 

 

to installation.

•   Prior  to  initial  installation,  install  a  shut-off  valve  (not 

included) from the water supply.

•   Thoroughly flush all water lines and fittings of all foreign 

matter before connecting to the cooler. Failure to do so 

will void warranty.

•   Check for any leaks before initial operation.

•   DO NOT attempt to repair or replace any part of your 

appliance  unless  it  is  specifically  recommended  in 

this manual. All other services should be referred to a 

qualified technician.

•  For use with clean, clear potable drinking water only.

•   Shut-off water supply during installation to reduce risk 

of water damage. 

•   Ensure  proper  ventilation  by  allowing  appropriate 

clearance of housing louvers to the wall on each side 

of the cooler, as specified in rough-in guide.

•   NEVER wire the compressor directly to an electrical supply.

•  DO NOT allow children to play with the appliance.

•   Interior of unit may contain sharp edges. Wear gloves 

when handling or servicing unit.

•  Failure to follow installation instructions will void warranty.

Note:  These fixtures are intended for indoor commercial 

use  only.  Do  not  expose  to  freezing  temperatures. 

The  grounding  of  electrical  equipment  to  water  lines  is 

a  common  procedure.  This  grounding  may  be  in  the 

building or occur away from the building. This grounding 

can  cause  electric  feedback  into  the  water  cooler 

creating an electrolysis which creates a metallic taste or 

causes the water metal content to increase. Connect to 

water supply using non-conductive materials.

Model 761219

b82045fc-0b136962-90871f19-f891407c

TM

TM

Read this manual thoroughly prior to 

installation, operation or maintenance. 

Keep these instructions in a safe location 

for future reference.  For questions, visit 

globalindustrial.com or contact Customer 

Service at 1-800-645-2982.

System 761219 certified by IAPMO 
R

&

T against to NSF/ANSI/CAN 372 

for lead free compliance

Содержание 761219













Отзывы: