gledhill SysteMate 125, Инструкции по установке и обслуживанию

Страница: 5 / 44

Supplied By www.heating spares.co Tel. 0161 620 6677
Page 4 Page 5
SY
STEMA
TE
2000
l e d o M 5 2 1 M S 5 4 1 M S 5 8 1 M S 0 1 2 M S 5 2 2 M S
) y t p m e ( t h g i e W g k 5 6 g k 8 6 g k 2 7 g k 9 8 g k 1 0 1
)l l u f ( t h g i e W g k 0 8 1 g k 3 9 1 g k 2 2 2 g k 9 5 2 g k 1 9 2
p m u P W H D 0 5 / 5 1 s o f d n u r G 0 5 / 5 1 s o f d n u r G 0 5 / 5 1 s o f d n u r G 0 5 / 5 1 s o f d n u r G 0 5 / 5 1 s o f d n u r G
p m u P g n i t a e H 0 5 / 5 1 s o f d n u r G 0 5 / 5 1 s o f d n u r G 0 5 / 5 1 s o f d n u r G 0 6 / 5 1 s o f d n u r G 0 6 / 5 1 s o f d n u r G
p m u P r e li o B 0 5 / 5 1 s o f d n u r G 0 5 / 5 1 s o f d n u r G 0 5 / 5 1 s o f d n u r G 0 6 / 5 1 s o f d n u r G 0 6 / 5 1 s o f d n u r G
e p i p g n i t a e h / y r a m i r P
s n o i t c e n n o c
m m 2 2 m m 2 2 m m 2 2 m m 8 2 m m 8 2
e p i p W H D & W C M
s n o i t c e n n o c
m m 2 2 m m 2 2 m m 2 2 m m 2 2 m m 2 2
n o i s n a p x e / d e e f d l o C
n o i t c e n n o c
m m 5 1 m m 5 1 m m 5 1 m m 5 1 m m 5 1
t n e v n e p o y t e f a S
n o i t c e n n o c
m m 2 2 m m 2 2 m m 2 2 m m 2 2 m m 2 2
s n o i t c e n n o c y r a m i r P
e s u r e m m u s r o f (
)l i a r l e w o t m o o r h t a b
m m 5 1 m m 5 1 m m 5 1 m m 5 1 m m 5 1
n o i t c e n n o C n i a r D '' 1⁄2 R '' 1⁄2 R '' 1⁄2 R '' 1⁄2 R '' 1⁄2 R
d a e H m u m i x a M
e r o t S l a m r e h T
s r e t e m 0 1 s r e t e m 0 1 s r e t e m 0 1 s r e t e m 0 1 s r e t e m 0 1
e r u s s e r p m u m i x a M
t i u c r i c g n i t a e h
r a b 3 r a b 3 r a b 3 r a b 3 r a b 3
e r u s s e r p m u m i x a M
r e t a w c i t s e m o d
r a b 5 r a b 5 r a b 5 r a b 5 r a b 5
li o c y r a m i r p f o e m u l o V
) s e r t il (
0 . 2 0 . 2 0 . 2 0 . 4 0 . 4
e t a r w o lf r e t a w t o H n i m / s t l 5 3 o t p u n i m / s t l 5 3 o t p u n i m / s t l 5 3 o t p u n i m / s t l 5 3 o t p u n i m / s t l 5 3 o t p u
e z i s r e li o b x a M k 5 1 W k 0 2 W k 5 2 W k 0 3 W k 5 3 W
' h c t i w S ' W k 9 W k 9 W k 9 W k 9 W k 9
s e p y t g n il l e w D l a c i p y T
s m o o r d e B 3 - 1 3 - 2 4 - 2 5 - 3 6 - 4
s m o o r h t a B 1 1 2 1 2 2 3 4
r e w o h s e t i u s - n E 1 2 1 4 2 4 2 0
1.2 TECHNICAL DATA
Notes:-
1. The SysteMate 225 appliance is suitable for use in large properties because it produces the same ‘peak hour output’
as a typical 250 - 320 litre unvented cylinder. For properties requiring the SM 225 the incoming main should be a
minimum of 32mm MDPE with a pressure of not less than 2 bar dynamic and an adequate flow in line with the pipe sizing
calculations. In many cases, properties of this size will benefit from having 2 smaller sized appliances located adjacent
to the areas of peak hot water use which will increase the available flow rate and may remove the need to provide trace
heating on the hot water distribution.
2. The plastic F & E cistern complete with fittings and the expansion vessel are supplied separately.
3. The flow rates are based on a 35°C temperature rise and assume normal pressure and adequate flow to the appliance. The actual
flow rate from the appliance is automatically regulated to a maximum of 28 litres/min.
4. Models are available in Hard and Soft water versions (suffixed ‘H’ or ‘S’).
5. Unit is supplied on a 100mm high installation base.
6. The domestic hot water outlet temperature is automatically regulated to approximately 55°C at the bath flow rate of 18 litres/min
recommended by BS 6700. The temperature is not user adjustable.
7. The maximum boiler size shown above is for the standard pump fitted and for a typical system. The designer/installer must
calculate the suitability of the standard pump as part of normal design procedures.
8. The expansion vessel sizes shown above have been calculated to be adequate for typical systems. The designer/installer must
calculate their suitability for the actual system and provide an extra vessel if required.
1.0 DESIGN