background image

Page 7

General Design Considerations

The cupboard footprint needs to be at least 
650mm square for units up to 300 litres, 730mm 
for 400 litre units.

The base chosen for the cylinder should be level 
and capable of supporting the weight of the unit 
when full of water as shown in General Data.  The 
discharge pipework for the safety valves must 
have a minimum fall of 1 : 200 from the unit to a 
safe discharge point.  All exposed pipework should 
be insulated and the unit should NOT be fi xed in a 
location where the contents could freeze.

The pipe connecting the boiler fl ow to the 
appliance must not be less than 22mm copper 
or equivalent.

Mains Water Supply

Existing properties with a 15mm supply will be 
satisfactory provided the local mains pressure 
is good, but should be confined to single 
bathroom properties.  For new properties where 
simultaneous demand is required to more than 
one bathroom or a bathroom and one or more 
en-suites, the communication and service pipe 
into the dwelling should be a minimum of 22mm 
(usually in the form of a 25mm MDPE supply).  
The minimum recommended static pressure 
to operate a Stainless Lite domestic system is 3 
bar.  There should be a fl ow of at least 30 litres 
per minute or above available into the property.  
Normally Stainless Lite provides well in excess 
of 40 litres/min in most conditions.  Flow rates 
for ALL mains pressure systems are subject 
to district pressures and system dynamic loss. 
Particularly on larger properties with more 
than one bathroom, the pipe sizes should be 
calculated in accordance with BS6700.

I.V.

Combination Valve

I.V.

If two Stainless Lites are coupled together the secondary inlet and outlet pipes must 
be balanced. The units must be fi tted on the same level.

Note: No valves must be fi tted between the expansion vessel and the storage 
cylinder(s).

INSTALLATION

INSTALLATION

Содержание StainlessLite HP180IND

































Отзывы: