gledhill Stainless Lite HP Indirect 180-400 litres Скачать руководство пользователя

Страница: 36 / 36

Gledhill Building Products Limited

Sycamore Estate, Squires Gate, Blackpool FY4 3RL Tel: 01253 474550 Fax: 01253 474551 [email protected]

After Sales Technical Support Tel: 01253 474584

Gledhill Building Products produce cylinders for use with a wide range of heat sources including;

Gas and oil boilers

Electricity

Air source heat pumps

Ground source heat pumps

Solar energy

Wood burning stoves

Further information on Gledhill products can be found at www.gledhill.net

“Only the best

is acceptable”

FM 02057

Protect your Gledhill

product after your

initial warranty period

For any spare part requirements on

this product simply scan the

QR code using your smart phone app

or go to www.gledhill-spares.net

On expiry of your initial warranty period, Gledhill Response Limited would be

pleased to provide further customer support with a range of services including:

Low cost annual repair and maintenance contracts direct from Gledhill

Annual servicing and safety checks

Expert response to ‘out of warranty’ breakdowns at fixed charges

Please call 08445 679898 or visit www.gledhill.net for further details

Due to a programme of continuous improvement Gledhill Building Products reserve the right to modify products without prior notice.

It is advisable to check the product technical detail by using the latest design and installation manuals available from our technical support team or on our website.

It is an offence to copy or adapt this document without consent of the owner.

Содержание Stainless Lite HP Indirect 180-400 litres





































Результаты поиска

Содержание Stainless Lite HP Indirect 180-400 litres

Отзывы:

Похожие инструкции для Stainless Lite HP Indirect 180-400 litres

Бренды по названию

Популярные бренды

gledhill Stainless Lite HP Indirect 180-400 litres, Инструкции по проектированию, установке и обслуживанию

Результаты поиска

Содержание Stainless Lite HP Indirect 180-400 litres

Отзывы:

Похожие инструкции для Stainless Lite HP Indirect 180-400 litres

Бренды по названию

Популярные бренды