gledhill PulsaCoil PCS 150 ECO Скачать руководство пользователя

Страница: 2 / 36

Page 2

Section

Page

DESIGN

Introduction

Technical Data

System Details

INSTALLATION

Site Requirements

Installation

Commissioning

Installation Review

SERVICING

Annual Service

Changing Components

Short Parts List

Fault Finding

ADDENDIX

Addendix A

Addendix B

Addendix C

Notes

Terms & Conditions 32

BENCHMARK

Commissioning Checklist

Service Record

ISSUE 6: AUGUST 2015

The Gledhill PulsaCoil range is a WBS

listed product and complies with the

HWA Specification for hot water only

thermal storage products. The principle was

developed in conjunction with British Gas.

This product is manufactured under an ISO

9001:2008 Quality System audited by BSI.

Gledhill’s first priority is to give a high quality

service to our customers.

Quality is built into every Gledhill product

and we hope you get satisfactory service

from Gledhill.

If not please let us know.

Benchmark places responsibilities on both manufacturers and installers. The purpose is to

ensure that customers are provided with the correct equipment for their needs, that it is

installed, commissioned and serviced in accordance with the manufacturers instructions

by competent persons and that it meets the requirements of the appropriate Building

Regulations. The Benchmark Checklist can be used to demonstrate compliance with

Building Regulations and should be provided to the customer for future reference.

Installers are required to carry out installation, commissioning and servicing work in

accordance with the Benchmark Code of Practice which is available from the Heating

and Hot Water Industry Council who manage and promote the Scheme. Visit www.

centralheating.co.uk for more information.

For further information on the HWA Charter Membership, please refer to the HWA website

hotwater.org.uk.

Содержание PulsaCoil PCS 150 ECO





































Результаты поиска

Содержание PulsaCoil PCS 150 ECO

Отзывы:

Похожие инструкции для PulsaCoil PCS 150 ECO

Бренды по названию

Популярные бренды

gledhill PulsaCoil PCS 150 ECO, Руководство по установке

Результаты поиска

Содержание PulsaCoil PCS 150 ECO

Отзывы:

Похожие инструкции для PulsaCoil PCS 150 ECO

Бренды по названию

Популярные бренды