gledhill PulsaCoil PCS 150 ECO страница 11 Скачать руководство пользователя

Страница: 11 / 36

Page 11

Electrical Installation

The Schematic arrangement of the wiring within

the PulsaCoil Stainless is shown above.

The whole of the electrical installation shall be

designed and installed by a competent person

fully in accordance with the latest edition of the

Requirements for Electrical installations BS 7671.

The PulsaCoil Stainless appliance is provided

with two side entry 3kW immersion heaters and

has been designed to generally operate with an

off peak supply.

The lower immersion heater heats the whole of

the contents and is normally connected to the

off peak supply.

The upper immersion heater is positioned at

a level on the PulsaCoil Stainless to heat the

top 66 - 111 litres of the store - see Technical

Data Table on page 5. This is connected to the

unrestricted on peak supply and is switched

manually by the householder using the button

on the boost controller.

The size of the appliance and the need to use

the on peak boost facility is reduced if a better

off peak tariff can be agreed with the electrical

supply company - see Model Selection Guide

on page 5.

Wiring The PulsaCoil With A Split Consumer

Unit I.e. Separate On And Off Peak Supplies.

Historically this has been the typical supply

method and no special wiring arrangements

are required.

DHW

Pump

Scale

Inhibitor

Fitted To

Hot Water

Outlet

ON PEAK

230V, 50Hz

20A

OFF PEAK

230V, 50Hz

20A

Immersion

(Off Peak)

Immersion

(On Peak)

PulsaCoil Stainless Schematic Wiring Diagram

HUBA Flow Sensor
PHE Inlet Sensor
Store Sensor

Boost

Controller

3kW

OFF

B16

Off Peak
Element

OFF

20 Amp

MCB

B16

MCB

On Peak
Element

20 Amp

Double Pole

Isolator

Double Pole

Isolator

METER

Twin Tariff Restricted Off Peak Connections

Twin Tariff Consumer Only

RESTRICTED

OFF PEAK

SUPPLY

24 HOUR

DOMESTIC

SUPPLY

ON PEAK 3KW

OFF PEAK 3KW

Rate1

Rate 2

Boost

Controller

3kW

Control

Board

DESIGN

SYSTEM DETAILS

Содержание PulsaCoil PCS 150 ECO





































Результаты поиска

Содержание PulsaCoil PCS 150 ECO

Отзывы:

Похожие инструкции для PulsaCoil PCS 150 ECO

Бренды по названию

Популярные бренды

gledhill PulsaCoil PCS 150 ECO, Руководство по установке

Результаты поиска

Содержание PulsaCoil PCS 150 ECO

Отзывы:

Похожие инструкции для PulsaCoil PCS 150 ECO

Бренды по названию

Популярные бренды