gledhill PulsaCoil PCS 150 ECO Скачать руководство пользователя | Manualshive

Страница: 16 / 36

background image

Page 16

Pipework Connections

The position of the pipework connections is

shown opposite. The exact location dimensions

are listed in the Technical Data section of this

manual.

All the connections are also labelled on the

appliance. It is essential that the pipework is

connected to the correct connection.

Connections A and B are plain ended copper

pipe.

Connection C and D compression fittings.

Connection E is RC½ (½ in BSPT internal)

A - 22mm Safety open vent

B - 22mm Cold feed/expansion

C - 22mm Incoming mains cold water

D - 22mm Domestic hot water

E - ½” Drain tap connection

Note

: The safety open vent and cold feed/

expansion must be connected to the top up

cistern using the pipework assembly provided.

Do not alter or connect any pressure-relief

device to the vent pipe of this water heater.

All factory made joints should be checked after

installation in case they have been loosened

during transit.

The fittings for the top up cistern should be

installed following the instructions provided

and the cistern fitted on its supports/top of

the appliance.

The cold feed/expansion and safety open vent

should be installed between the appliance and

the top up cistern.

Figure 1.6

C

D

B

A

E

INSTALLATION

INSTALLATION

«
...
14
15
16
17
18
...
»

Содержание PulsaCoil PCS 150 ECO





































Отзывы:

Нет отзывов

Похожие инструкции для PulsaCoil PCS 150 ECO

Бренд: Water Depot Страницы: 31

ACQUITY UPLC I-Class IVD

Бренд: Waters Страницы: 98

Бренд: Calpeda Страницы: 32

Бренд: RainSoft Страницы: 16

Бренд: Zehnder Rittling Страницы: 20

GreenSpec HTHB-HVRGRN

Бренд: Halsey Taylor Страницы: 7

Бренд: Zehnder Pumpen Страницы: 32

SMART ECG 1000 A

Бренд: Airtecnics Страницы: 22

Бренд: Culligan Страницы: 58

Бренд: EQUATION Страницы: 34

Бренд: EBARA Страницы: 69

Бренд: Harbor Freight Tools Страницы: 10

Бренд: BN Thermic Страницы: 4

Бренд: Wacker Neuson Страницы: 52

Бренд: Wacker Neuson Страницы: 60

CLI U12 SD0F1110 NG B/U

Бренд: Velux Страницы: 56

Бренд: Zibro Страницы: 75

Бренд: La Hacienda Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды