gledhill PulsaCoil PCS 150 ECO Скачать руководство пользователя | Manualshive

Страница: 19 / 36

background image

Page 19

INSTALLATION

INSTALLATION REVIEW

Circulating fluid in thermal store pipework

• The PulsaCoil Stainless and the thermal store pipework must have completed filling

prior to switching the electricity supply to the PWM controller PCB. If there is no

water in these pipes then there may be significant wear on the PWM pump.

• This can be confirmed by

- Checking the thermal store pipework servicing valves are open

- Loosening the connection points on the thermal store pipework in a systematic

manner and checking for water presence.

- Confirming that the feed and expansion tank has completed filling and the

servicing valve is open.

Cold mains water supply to plate heat exchanger and hot water taps

• Confirm that the CW mains stop valve is open

• Open all HW taps and confirm that the water runs freely and that any air is bled

from the DHW system

• Determine the maximum flow rate obtained and record

• 15l/min for all PulsaCoil products currently limited with a flow restrictor

• If flow rate not as expected determine the cause and rectify

- clean inline strainer

- check the flow restrictor is present and not blocked. It is located in the top of

the inline strainer

Power on

• Switch on the Local fuse spur and observe the PWM pump

• The green LED will flash showing the pump has a power supply and is in standby

mode.

• Open a HW tap and observe the PWM pump

• The green LED will be constantly lit showing the pump has a power supply and is

running to generate HW

NOTE: -The thermal store will only produce hot water when it is hot enough. A mid

40°C thermal store temperature will provide some hot water, higher thermal store

temperatures will provide more.

Inline scale inhibitor (if fitted)

• Check power supply

• PWM Controller PCB supplies a maximum of 12vDC/300mA to the Scale inhibition

board. (From J3)

• Check dip switches set correctly

• The correct settings for tube diameter 22mm is switch no. 3 on.

• Switch no. 4 can be either on or off.

• If the switch no. 4 is turned on the output electromagnetic field is generated

harmoniously otherwise the field is generated inharmoniously.

«
...
17
18
19
20
21
...
»

Содержание PulsaCoil PCS 150 ECO





































Отзывы:

Нет отзывов

Похожие инструкции для PulsaCoil PCS 150 ECO

Бренд: Jet-Line group Страницы: 20

Бренд: NARVI Oy Finland Страницы: 44

Standard Series

Бренд: Facilities Resource Group Страницы: 61

Бренд: RBI Страницы: 48

Бренд: vacuubrand Страницы: 24

Бренд: Watts Страницы: 8

Бренд: Watson-Marlow Страницы: 128

Бренд: Zip Страницы: 16

Бренд: Karibu Страницы: 60

Бренд: DAB Страницы: 40

Бренд: A.O. Smith Страницы: 44

Бренд: Bimar Страницы: 48

Бренд: DEFA Страницы: 12

GQ-C3257WX-FF US

Бренд: Noritz Страницы: 32

Бренд: EBARA Страницы: 20

Бренд: BM2 BIEMMEDUE Страницы: 8

Бренд: vacuubrand Страницы: 70

Бренд: L.B. White Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды