background image

Page 13

The appliance is designed to be installed in an airing/cylinder cupboard and the 

relevant minimum dimensions are provided in the Technical Data section of this 

manual.

Because of the ease of installation we recommend that the cupboard construction is 

completed and painted before installation of the appliance. The cupboard door can 

be fitted after installation.

If the unit needs to be stored prior to installation it should be stored upright in a dry 

environment and on a level base/floor.

Installation and maintenance access is needed to the front of the appliance and above 

the Top up cistern. See the Technical Data section of this manual for further details.  

The minimum dimensions contained in the Technical Data section of this manual 

allow for the passage/connection of pipes to the appliance from any direction as long 

as the appliance is installed on the installation base provided. If the installation base 

is not used extra space may be needed to allow connection to the pipework and the 

whole of the base area should be continuously supported on a material which will 

not easily deteriorate if exposed to moisture.

The floor of the cupboard needs to be level and even and capable of supporting the 

weight of the appliance when full. Details of the weight when full is provided in the 

Technical Data section of this manual.

The  appliance  is  designed  to  operate  as  quietly  as  practicable.  However,  some 

noise (from pumps etc) is inevitable when hot water is being used. This will be most 

noticeable if the cupboards are located adjacent to bedrooms, on bulkheads, or at 

the mid span of a suspended floor. Some noise may also be experienced from the 

immersion heaters as the store approaches its design temperature.

Cupboard temperatures will normally be slightly higher than in a conventional system 

and the design of the cupboard and door will need to take this into account. No 

ventilation is normally required to the cupboard.

The separate Top up cistern will need to be located on top of the appliance or at high 

level in the cupboard housing the PulsaCoil Stainless. The dimensions and clearances 

are provided in the Technical Data section of this manual. The location will need to 

provide a suitable route for the cold feed expansion pipe as well as the open safety 

vent pipe. The location will also need to provide a suitable route and discharge position 

for the warning/overflow pipe and the ballvalve supply from the mains cold water 

system (if provided) if these have been ordered as an optional extra.

Note: The standard appliance is supplied with a cistern without a ballvalve/

overflow for filling manually. 

An electrical supply must be available which is correctly earthed, polarized and in 

accordance with the latest edition of the IEE requirements for electrical Installations 

BS 7671.

The electrical mains supply needs to be 230V/50Hz.

The sizes/types of electrical supplies must be as detailed in System Details section 

of this manual. A means for disconnection from the supply mains having a contact 

separation in all poles that provides full disconnection under over voltage category 

III conditions must be incorporated in the fixed wiring in accordance with the wiring 

rules. This shall be located within 1m of the appliance and only serve the appliance.

The hot and cold water ‘first fix’ pipework should be terminated 50mm above the 

finished floor level in accordance with the dimensions provided in the Technical Data 

section of this manual.

INSTALLATION

SITE REQUIREMENTS

Содержание PulsaCoil PCS 120

































Отзывы: