gledhill PulsaCoil PCS 120 Скачать руководство пользователя страница 22

Страница: 22 / 32

Page 22

APPLIANCE CONTROL BOARD (A.C.B)

Fuse

T3.15L 250V

2 DIGIT ACB BOARD DISPLAY FLOW CHART

Press S2

S2 S1

Press

Fault code indicator

block outs

Press

Fault code indicator

lock outs

Press

Control set-point

reading

Press

Sensor temperature

reading

Normal - standby state

Indicate system status

2 digit

display

2 push

buttons

Main

processor

Appliance Control Board

The appliance control board (shown opposite) has a 2 digit display and 2 push buttons

which are used to check the status of the appliance, check and set its identity and

interrogate it for the current faults and the fault history.

The 2 digit display is controlled by 2 buttons S1 and S2. The flow chart of display

modes is shown above. Generally, each press of button S2 cycles the display from top

to bottom and each press of button S1 cycles the display functions from left to right.

The button S2 is also used to reset the appliance i.e. clear the lockout errors and reset

the appliance. (Note: Appliance resetting can also be carried out using the push

button on the front panel)

Note: The board is used on a range of products and not all terminals are used on

every appliance.

Display in Normal (Standby) Mode

In the standard/normal mode the 2 digit display indicates the status of the appliance

inputs and outputs by switching on the appropriate segments of the display - see

page 24 for details.

Appliance Type Selection

The PulsaCoil is fitted with an identity (ID) resistor which is read by the controller

for comparison with the appliance type (code) set on the controller. The two must

match for the controller/appliance to function. Therefore if either the appliance code

setting or the ID resistor is wrong, the appliance will shut down safely and flag the

error code until the fault is rectified. The controller codes and the ID resistor values

for the PulsaCoil are 03 and 3K3 respectively.

The procedure for checking and setting the

appliance code on the controller is described

below.

• The appliance selection menu (A0 ... A9) on

the controller is hidden. It is only possible to

get to the appliance selection using the reset

button (Left hand, S2) on the main board.

• When going from the show ‘ locking error’ to

show ‘blocking error’ menu (see opposite),

do not release the button but hold it for 10

seconds. The display will change from ‘c’ to

‘A’. At this stage the push button (S2) can be

released.

• The appliance type can now be selected by

using right hand push button, S1, e.g. for

this appliance A03.

Press the reset button, S2, to accept the setting.

If the selected appliance code does not match

with the ID resistor fitted to the appliance, then,

an error ‘33’ will be displayed.

SERVICING

FAULT FINDING

Содержание PulsaCoil PCS 120

































Результаты поиска

Содержание PulsaCoil PCS 120

Отзывы:

Похожие инструкции для PulsaCoil PCS 120

Бренды по названию

Популярные бренды

gledhill PulsaCoil PCS 120, Инструкции по проектированию, установке и обслуживанию

Результаты поиска

Содержание PulsaCoil PCS 120

Отзывы:

Похожие инструкции для PulsaCoil PCS 120

Бренды по названию

Популярные бренды