gledhill BM 185 страница 3 Скачать руководство пользователя | Manualshive

Страница: 3 / 46

background image

Page 3

BOILERMA

TE

2000

1.0 DESIGN

1.1 INTRODUCTION

T h e s e i n s t r u c t i o n s s h o u l d b e r e a d i n
conjunction with the Installation and Servicing
Instructions issued by the manufacturers of
the heat source e.g. the boiler used.

Any water distribution and central heating
installation must comply with the relevant
recommendations of the current version of
the Regulations and British Standards listed
below:-

Gas Safety Regulations
Building Regulations
I.E.E. Requirements for Electrical Installations
Water Regulations

British Standards
BS6798, BS5449, BS5546, BS5440:1, BS5440:2,
CP331:3, BS6700, BS5258, BS7593 and BS7671.

A competent person as stated in the Gas
Safety Regulations must install the BoilerMate
heating system. The manufacturer’s notes
must not be taken as overriding statutory
obligations.

The BoilerMate 2000 is only suitable for use
with an open vented central heating system.

The BoilerMate 2000 is not covered by section
G3 of the current Building Regulations and is
therefore not notifi able to Building Control.

The information in this manual is provided to
assist generally in the selection of equipment.
The responsibility for the selection and
specifi cation of the equipment must however
remain that of the customer and any Designers
or Consultants concerned with the design and
installation.

Please Note: We do not therefore accept any
responsibility for matters of design, selection
or specifi cation or for the effectiveness of an
installation containing one of our products
unless we have been specifi cally requested
to do so.

All goods are sold subject to our Conditions
of Sale, which are set out at the rear of this
manual.

In the interest of continuously improving
the BoilerMate range, Gledhill Water Storage
Ltd reserve the right to modify the product
without notice, and in these circumstances
this document, which is accurate at the time
of printing, should be disregarded. It will
however be updated as soon as possible after
the change has occurred.

«
1
2
3
4
5
...
»

Содержание BM 185















































Отзывы:

Нет отзывов

Похожие инструкции для BM 185

VOGUE MAX COMBI 26

Бренд: Ideal Boilers Страницы: 80

Бренд: IDEAL Страницы: 16

Бренд: ideal commercial Страницы: 66

Classic FF 360 LF

Бренд: Ideal Boilers Страницы: 4

Aerco Benchmark 5000

Бренд: Watts Страницы: 76

Classic Slimline FF 230

Бренд: IDEAL Страницы: 40

GOLD CGS 550-110-260/0107

Бренд: Weil-McLain Страницы: 64

Бренд: Roca Страницы: 11

Бренд: Blodgett Страницы: 2

Proteus Plus Blue 24 kW

Бренд: E.C.A. Страницы: 35

Бренд: E-Tech Страницы: 44

PRESTIGE Solo 110

Бренд: Prestige Страницы: 40

Бренд: Aerco Страницы: 210

Mod Con 300 VWH

Бренд: HTP Страницы: 73

Elite XL ELX-1000

Бренд: HTP Страницы: 87

BRAVA One HE 25

Бренд: Sime Страницы: 108

Бренд: Immergas Страницы: 52

Mexico Super RS440

Бренд: Ideal Boilers Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды