manualshive.com logo in svg

gledhill BM 185, Инструкции по установке и обслуживанию

Поделиться
Скачать
gledhill BM 185 Скачать руководство пользователя страница 30

Page 30

6.  DO ensure that the water level in the F & E cistern is at least 250mm above 
 the 

highest point on the radiator circuit or the highest point of the system.

7.  DO insulate any exposed pipework in the BoilerMate cupboard.

8.  DO plumb the overflow/warning pipe in a 20mm internal diameter pipe 
 

material which is suitable for use with a heating F & E cistern, in accordance 

 

with BS 5449 (such as copper) and ensure it has a continuous fall and 

 

discharges in a conspicuous external position.

9.  DO check the pump settings
 

a. The boiler pump should be set to give a temperature difference across 

 

the boiler of 8°C or less.

 

b. The heating pump should be set to give a temperature difference across 

 the 

fl ow and return of not more than 11°C.

 

c. The hot water plate heat exchanger pump should be set at maximum.

10.  DO ensure that the bypass valve for the heating system (if fitted) is set 
 correctly.

11.  DON’T use a combined feed and vent on BoilerMate installations.

12.  DON’T use a BoilerMate on a sealed primary i.e. closed system.

13.  D O N ’ T   u s e   p i p e   s m a l l e r   t h a n   2 8 m m   between the boiler and the 

 

BoilerMate when the boiler rating exceeds 20kW (about 68,000 Btu/h).

14.  DON’T use dipped flow and return between the boiler and the BoilerMate 
 

unless the boiler is fitted with an overheat thermostat.  If necessary check 

 

with the suppliers of the boiler.

15.  DON’T operate the ‘switch’ backup facility until the system is fully fi tted, vented  
 and 

commissioned.

16. DON’T place any clothing or other combustible materials against or on top of  
 this 

appliance.

2.0  INSTALLATION

2.3 COMMISSIONING

Important Do’s and Don’ts

1.  

DO check the incoming mains water pressure and fl ow rate are adequate.  

 

 (The preferred range of mains pressure is 2-3bar).

2.  

DO check that all connections are in accordance with the labelling on the 

  

thermal 

store.

3.  

DO adjust the ballvalve so that the water level in the F & E cistern when 

         the   system is cold is correct and does not overfl ow when the whole of the 
 

 system is at maximum temperature.

4.  

DO make sure that there is adequate clearance above the F & E 

 

 cistern to   service the ballvalve.

5.    DO ensure that the range rated appliances are set at the highest output     
 

 and the boiler thermostat is set to maximum for all boilers.

Содержание BM 185















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды