manualshive.com logo in svg

gledhill BM 185, Инструкции по установке и обслуживанию

Поделиться
Скачать
gledhill BM 185 Скачать руководство пользователя страница 27

Page 27

BOILERMA

TE 

2000

2.3 COMMISSIONING

2.0  INSTALLATION

Primary Water System Treatment

Although the BoilerMate 2000 has no special 
water treatment requirements, the radiators 
and other parts of the circuit will benefit 
from the application of a scale and corrosion 
inhibitor such as Sentinel X100 or a Protector 
such as Fernox MB1.

When determining the quantity of inhibitor 
required, be sure to allow for the increased 
volume of water in the primary circuit due to 
the thermal store - see section 1.2 Technical 
Data for volumes.

In most cases the quantities shown opposite 
will be suitable for a typical 3/4 bed property.

POWERFLUSHING/CLEANING OF THE HEATING 
SYSTEM

If it is proposed to ‘powerfl ush’ the heating 
system we would recommend that the 
BoilerMate appliance is isolated from the 
heating system being cleaned.  Failure to do 
this could seriously damage the appliance.

When carrying out the work always comply 
fully with the manufacturers instructions for 
the powerfl ushing equipment being used.

If in any doubt please consult our Technical 
Helpline.

Open the incoming stop valve and fi ll the domestic mains cold and hot water 
systems.

Fill the whole of the primary heating system with potable water through the 
feed and expansion cistern.

Check the water level in the feed and expansion cistern and adjust the ballvalve 
if necessary.

Check the whole of the primary heating and domestic hot and cold distribution 
systems for leaks.

It is essential that all systems function properly for optimum performance.  

To achieve this, the primary system should be commissioned in accordance with 
good practice and generally in accordance with the requirements of BS 6798, 
BS 5449 and BS 7593.

Full details of the requirements are given in PAS 33:1999 under Section 10 
Commissioning.

When using either cleansing or corrosion 
inhibitor chemical, the manufac turers 
instructions must be followed.

Cleansing the Primary System

When determining the quantity of cleanser 
required, be sure to allow for the increased 
volume of water in the primary circuit due 
to the thermal store.

In most cases the quantities shown opposite 
will be adequate for a typical 3/4 bedroom 
property.

Model

Volume to be added to the system (litres)

Corrosion inhibitor agent

Sentinel X100

Fernox MB1

BM125

1¼

1¼

BM145

1½

1½

BM185

2

2

BM210

2¼

2¼

BM225

2½

2½

Model

Volume to be added to the system (litres)

Cleansing agent

Sentinel X300

Fernox Superfl oc

BM125

1½

1½

BM145

1½

1½

BM185

2

2

BM210

2¼

2¼

BM225

2½

2½

Содержание BM 185















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды