Girard Systems 98GC274B Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 21

background image

17

To find the batteries turn the wall switch over and using a small flate screw driver pull
the cover off, the cover has the word

“open”

on the right bottom corner, see Fig.9

below.

•

The Battery compartment, (into which three CR2430 3v Lithium battery should
be inserted as shown)

Fig.9

Magnetic Holder.- This new G link transmitter was designed with a magnetic plate
holder to keep it in place and make it more user friendly. See Fig 10 below.

Fig.10

«
...
15
16
17
18
19
...
»

Содержание 98GC274B






















Отзывы:

Нет отзывов

Похожие инструкции для 98GC274B

Бренд: FAAC Страницы: 12

Бренд: NEC Страницы: 146

Бренд: C.Nord Страницы: 100

CoreBuilder 9000

Бренд: 3Com Страницы: 78

Бренд: B&R Industries Страницы: 89

Бренд: Laars Страницы: 28

Бренд: VAT Страницы: 27

MorphoAccess SIGMA Extreme Series

Бренд: Idemia Страницы: 31

Бренд: ICP DAS USA Страницы: 148

Бренд: ICMA Страницы: 8

PXI-6683 Series

Бренд: National Instruments Страницы: 4

Бренд: National Instruments Страницы: 9

Бренд: National Instruments Страницы: 11

Бренд: National Instruments Страницы: 29

Бренд: National Instruments Страницы: 11

Бренд: National Instruments Страницы: 7

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 21

FieldPoint FP-1001

Бренд: National Instruments Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды