Gima 35124 Скачать руководство пользователя страница 13

Страница: 13 / 64

3.2 Battery Installation

1. Ensure that the Gima Vital Signs Monitor is not connected to AC power supply and is turned off.

2. Open the battery cover and move the locking bar aside.

3. Put the battery into the box and move the locking bar back. Please note that the battery cables should be

outward.

4. Connect the battery cable plug to the battery power socket in right direction, as shown in figure 3.6.

5. Arrange the wires and close the battery cover.

Figure 3.6 Battery Installation

Warning:

1. To avoid battery damage always remove battery(s) before shipping or storage.

2. It is recommended to use the battery specified by the manufacturer.

3. The battery service life depends on how frequently and for how long it is used. For a properly maintained

and stored lead-acid or lithium battery, its service life is about 2 or 3 years respectively. For more often used

models, service life can be less. We recommend replacing lead-acid battery every 2 years and lithium bat-

tery every 3 years.

Caution:

1. Keep the battery out of the reach of children.

2. Do not disassemble battery.

3. Do not dispose of in fire.

4. Do not cause them to short circuit.

3.3 Installation

3.3.1 Opening the Package and Check

1. Open the package, take out the Gima Vital Signs Monitor and accessories from the box carefully and place

them on a safe sand table and surface.

2. Open the accompanying document to sort the accessories according to the packing list.

Battery

Locking bar

Battery cover tether

Battery cable

Battery cable plug

Battery power socket

Battery power cable

Battery cover

Содержание 35124

































































Результаты поиска

Содержание 35124

Отзывы:

Похожие инструкции для 35124

Бренды по названию

Популярные бренды

Gima 35124, Руководство пользователя

Результаты поиска

Содержание 35124

Отзывы:

Похожие инструкции для 35124

Бренды по названию

Популярные бренды