GILBARCO VEEDER-ROOT FlexPay IV CRIND Advantage Series Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 44

background image

MDE-5224F

16

SECTION 4 - INSTALLATION

4

DCM2.1 Assembly

The DCM2.1 Assembly Board (M15399A001) mounts in the same location as the M13124A001 AFP Board,

with the same cable connections. The DCM2.1 Board provides the same functionality as the AFP, along with
a high-speed data connection for the Applause Media System, Insite360 Encore, and future EMV
applications. Similar to AFP, the M15399A001 DCM2.1 Board can host two GSoM boards for Applause Media
System. On the rear side of the M14576A001 DCM2 Board, there is an SSoM for Insite360 Encore.

Figure 6: Mounting DCM2.1 Assembly

M15242A001 Cables to the M7
UPM

M15242A001 Cables
to the M7 Universal
Payment Module
(UPM)

M02993A005 Two-wire Cables

Power Cable

Note: P304 is dedicated for external Ethernet connections (FlexPay Connect and Direct Ethernet) to protect against

surge suppression.

Laptop Service Port

Note: The Advantage Series does not support the ZMODEM option for Insite360 Encore.

«
...
18
19
20
21
22
...
»

Содержание FlexPay IV CRIND Advantage Series













































Отзывы:

Нет отзывов

Похожие инструкции для FlexPay IV CRIND Advantage Series

Бренд: CAIRE Страницы: 38

Бренд: laerdal Страницы: 8

Бренд: LAHTI PRO Страницы: 16

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 8

Бренд: Velleman-Kit Страницы: 32

Бренд: LSI Страницы: 24

Бренд: Crosley Страницы: 6

Бренд: Gambro Страницы: 273

Бренд: PMK Страницы: 24

Бренд: SteelFlex Страницы: 13

Бренд: York Fitness Страницы: 18

Бренд: FitEngine Страницы: 68

Бренд: Interacoustics Страницы: 2

Бренд: Proceq Страницы: 35

Бренд: Baehr Страницы: 64

Бренд: DARAY Страницы: 48

Mega Strobe III

Бренд: Chauvet Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды