GIGAMEDIA GGM FES08P2G Скачать руководство пользователя страница 47

Страница: 47 / 49

IGMP Snooping V1 & V2

A switch will, by default, flood multicast traffic to all ports in a broadcast domain. Multicast can

cause unnecessary load on host devices by requiring them to process packets they have not

solicited. The IGMP snooping is a feature that allows the switch to listen in on the IGMP

conversation between hosts and routers. By listening (also known as snooping) to these

conversations, the switch maintains a map of which ports (clients) need which multicast

stream (source). Multicast may be filtered which do not need them, Multicast may be

forwarded only to the IGMP group it joined.

IGMP Snooping

When this function is enabled, the switch will execute IGMP snooping version 1 and version 2

without the intervention of CPU. The IGMP report and leave packets are automatically

handled by the switch. The next setting, IGMP Leave Packet can be enabled or disabled.

After enabled, the Leave packet will be forwarded to IGMP router ports.

VLAN Uplink Setting

This switch does not implement Independent VLAN (IVL) MAC address table, it utilizes VLAN

uplink to emulate the function of IVL. An independent VLAN MAC address table is based on

both the source MAC address and the VLAN. In some application, if the Ethernet switch

cannot build the separate MAC address table for different VLANs, there will be a conflict of

MAC address table. To solve this problem, the switch controller utilizes the VLAN Uplink port

to emulate the usage of Independent VLAN MAC Address Table.

VLAN Uplink Setting

If VLAN uplink function is enabled and the destination port of an unicast packet is located at

the next VLAN, this packet will be forwarded to the uplink port. Choose the Uplink Port X for

the port ID. The Uplink X will be the uplink port of its VLAN.

Button



Update:

Apply all the settings you’ve made here.

Содержание GGM FES08P2G


















































Результаты поиска

Содержание GGM FES08P2G

Отзывы:

Бренды по названию

Популярные бренды

GIGAMEDIA GGM FES08P2G, Руководство пользователя

Результаты поиска

Содержание GGM FES08P2G

Отзывы:

Бренды по названию

Популярные бренды