manualshive.com logo in svg

Gigabyte E251-U70, Руководство пользователя, Страница: 7 / 111

Поделиться
Скачать
Gigabyte E251-U70 Скачать руководство пользователя страница 7

- 7 -

Table of Contents

Chapter 1  Hardware Installation ...................................................................................11

1-1  Installation Precautions .................................................................................. 11

1-2  Product Specifications

 .................................................................................... 12

1-3  System Block Diagram ................................................................................... 15

Chapter 2  System Appearance .....................................................................................17

2-1  Front View ...................................................................................................... 17
2-2  Rear View ....................................................................................................... 18
2-3  Front Panel LEDs and Buttons ....................................................................... 19
2-4  Rear System LAN LEDs ................................................................................. 20
2-5  Power Supply Unit LED .................................................................................. 21
2-6  Hard Disk Drive LEDs .................................................................................... 22

Chapter 3  System Hardware Installation ......................................................................23

3-1  Removing and Installing the Chassis Cover .................................................. 24
3-2  Removing and Installing the Fan Duct ........................................................... 25
3-3  Removing and Installing the Heat Sink .......................................................... 26
3-4  Installing the CPU and Heat Sink ................................................................... 27
3-5  Removing and Installing Memory ................................................................... 29

3-5-1  Six-Channel Memory Configuration

 ........................................................................29

3-5-2  Installing a Memory  ...............................................................................................30
3-5-3  DIMM Population Rule ............................................................................................30

3-6  Installing the GPU Card  ................................................................................ 31
3-7  Removing and Installing the Hard Disk Drive ................................................. 32
3-8  Replacing the Fan Assembly .......................................................................... 33
3-9  Removing and Installing the Power Supply .................................................... 34
3-10  Removing and Installing the Front Bezel Cover (Optional) ............................ 35
3-11  Cable Routing ................................................................................................ 36

Chapter 4  Motherboard Components ...........................................................................41

4-1  Motherboard Components ............................................................................. 41
4-2  Jumper Setting  .............................................................................................. 43

Chapter 5  BIOS Setup ..................................................................................................45

5-1  The Main Menu .............................................................................................. 47
5-2  Advanced Menu ............................................................................................. 50

5-2-1  Trusted Computing .................................................................................................51
5-2-2  Serial Port Console Redirection .............................................................................52

Содержание E251-U70
















































































































Отзывы:

Нет отзывов