manualshive.com logo in svg

Gigabyte E251-U70, Руководство пользователя, Страница: 31 / 111

Поделиться
Скачать
Gigabyte E251-U70 Скачать руководство пользователя страница 31

- 23 -

System Hardware Installation

3-6  Installing the GPU Card 

Before you install the GPU card:

Voltages can be present within the server whenever an AC power source is connected. This 

voltage is present even when the main power switch is in the off position. Ensure that the system 
is powered down and all power sources have been disconnected from the server prior to installing 
a GPU card. Make sure the system is not turned on or connected to AC power.

Failure to observe these warnings could result in personal injury or damage to the equipment.

Follow these instructions to install the GPU card:

1.  Lift up the GPU card cage.
2.  Remove the two screws securing the GPU card slot covers and remove the GPU slot covers.

3.  Insert the GPU card into the selected slot. Make sure the GPU card is properly seated.

4.  Install the two screws to secure the GPU card in place.

5.  Install the three screws to secure the GPU card bracket in place.

1

2

3

Содержание E251-U70
















































































































Отзывы:

Нет отзывов