background image

12

OPERATING INSTRUCTIONS

Lighting the Water Heater

Before lighting or re-lighting your water 
heater, make sure that you have read 
and understood all of the instructions 
and warnings in this manual and on 
your water heater. If you have any 
questions about lighting your water 

heater, immediately contact a qualified installer, 
service agency, or the gas supplier.

DO NOT

 light this water heater if:

•  It is not full of water.
•  The gas supplied does not match the type listed on 

the rating plate.

•  The sight glass or burner access door gasket has 

been damaged or broken.

•  Gasoline or other flammable vapours and liquids 

have been stored in the vicinity of the water heater.

Failure to follow these instructions can result in 
property damage, personal injury, or death.

FOR YOUR SAFETY, READ BEFORE LIGHTING

LIGHTING INSTRUCTIONS

WARNING: 

If you do not follow these instructions exactly,

a fire or explosion may result causing property damage, personal injury, or death.

A. This appliance has a pilot which must be lit by a
  piezo-electric spark gas ignition system. 

DO NOT

  open the inner door and attempt to light the pilot by hand.
B. 

BEFORE LIGHTING

, smell all around the appliance area

  for gas. Be sure to smell next to the floor because some
  gases are heavier than air and will settle on the floor.
 

WHAT TO DO IF YOU SMELL GAS

:

 - 

DO NOT

 try to light any appliance.

 - 

DO NOT

 touch any electric switch.

 - 

DO NOT

 use any phone in your building.

  - From a neighbour's phone, immediately call your gas
    supplier. Follow the gas supplier's instructions.

  - If you cannot reach your gas supplier, call
  the fire department.
C. Use only your hand to push in or turn the gas
  control knob. Never use tools. If the knob will
  not push in or turn by hand, do not try to repair it.
  Call a qualified service technician. Force or
  attempted repair may result in a fire or explosion.
D. 

DO NOT

 use this water heater if any part has been

  under water. Immediately call a qualified service
  technician to inspect the water heater and to 
  replace any part of the control system and any
  gas control which has been under water.

1. 

STOP

! Read the safety information above on this label.

2. Turn the temperature dial clockwise              to the
 "

PILOT LIGHTING

" position.

3. Depress slightly and turn the gas control knob
  clockwise              to the "OFF" position.

Gas control knob

shown in "OFF" position

Sight

glass

Piezo igniter

button

Thermocouple

Pilot

Burner

Note: The gas control knob cannot be
turned from "PILOT" to "OFF" unless the

knob is depressed slightly. Do not force.

4. Wait five (5) minutes to clear out any gas.

  Then smell for gas, including near the floor. 

  If you smell gas, 

STOP

! Follow "B" in the safety 

  information above (to the left) on this label. 

  If you don't smell gas, go to the next step.

5. Remove the outer access door.

6. Locate the piezo igniter button.

7. Look into the sight-glass window on

  the inner access door to view the pilot.

8.  Turn the gas control knob
   counterclockwise
   to the "PILOT" position.
9.  Depress and hold down the gas
   control knob. Immediately depress
   the piezo igniter button until you hear a
   "click'' sound, then release. Continue to hold down the
   gas control knob for approximately one (1) minute after
   the pilot is lit. If the pilot does not light, continue to
   depress and release the piezo igniter button. Release the
   gas control knob, and it should pop back up. The pilot should
   remain lit. If it goes out, repeat steps 3 through 8.
   - If the knob does not pop up when you release it, stop and
     immediately call a qualified service technician or gas supplier.
   - If the pilot will not stay lit after several tries, turn the
     gas control knob clockwise               to the "OFF" position
     and call a qualified service technician or the gas supplier.
10.  Replace the outer access door.
11.  Turn the gas control knob counterclockwise
                 to the "ON" position.
12.  Turn the temperature dial to the desired setting.

TO TURN OFF GAS TO APPLIANCE

1. Turn the temperature dial clockwise              to the "

PILOT LIGHTING

" position.

2. Depress slightly and turn the gas control knob clockwise             to the "

OFF

" position.

Electrode

Содержание UG30





















Отзывы: