background image

General Safety Precautions

Distributor:

Read the precaution below carefully as it contains important information about safe installation and 

maintenance.

This instruction must be conducted to all potential users.

The product must be used in visible place.

The manufacturer will not be held responsible for any damage caused by improper use of this unit. 

Do not use the door closer with the AD425S.

Do not put any obstacle in the door path when operating.

Do not allow children to play or stay within the field of action of the motorized door or gate. Keep remote 

control or any other control devices out of the reach of children, in order to avoid an unexpected accident 

happened. Do not attempt to modify or fix this unit. Contact your local distributor when any service is 

needed. 

To assure the finest performance, please follow the operation instructions. Contact qualified personnel 

to make regular maintenance checks. All installation, maintenance and repair work must be documented 

and made available to the user.

The following precautions are essential for the user.

Automatic Door Operator 

Manual

20

Содержание AD-425S























Отзывы: