background image

66

A C C E S S O R I E S

© G h o s t   C o n t r o l s   2 0 1 8   |   w w w . G h o s t C o n t r o l s . c o m

PREMIUM REMOTE TRANSMITTER | AXP1 

The premium remote transmitter (single or dual) provides the ability to open or close, enable or disable 

PartyMode

®

, determine gate opener system battery status, and can be quickly added as  

a new remote to an existing system. CR2032 Battery Included.

STANDARD REMOTE TRANSMITTER | AXS1
The standard remote transmitter will control up to two separate GHOST CONTROLS

®

 gate systems 

(single or dual) and it can be learned as a new remote to an existing system. CR2032 Battery Included.

WIRELESS KEYPAD | AXWK
The GHOST CONTROLS

®

 Premium Wireless Keypad is the superior gateway to your gate opener system 

and provides unprecedented control and capabilities. This outdoor keypad is more than just an access point 

for visitors to your home or property who do not have a remote transmitter because it also provides the 

ability for you to activate or deactivate additional features for your keypad such as VacationMode™.

ZOMBIELOCK® | AXZL
The patent pending ZombieLock

®

 will provide your home with the latest in automatic gate lock  

technology with advanced feedback to your GHOST CONTROLS

®

 gate controller.

LOCKING CLEVIS PIN | AXLC
The GHOST CONTROLS

®

 Locking Clevis Pin allows you to easily secure the gate operator arm to the 

mounting brackets with a padlock by replacing the Clevis pin included in the gate opener kit.
WIRED VEHICLE SENSOR | AXXV
The GHOST CONTROLS

®

 Vehicle Sensor is the easiest way to trigger your gate to open when a vehicle 

is trying to exit your property. This sensor is buried beneath the ground surface next to your driveway and 

connects into your gate controller box. 55’ cable included (cannot be spliced)
PREMIUM 10 WATT MONOCRYSTALLINE SOLAR PANEL  | AXDP 
The monocrystalline 10W solar panels are a great solution for anyone who is installing a gate operator 

system in a remote location that does not have easy access to 120V AC power or for those who do not  

want to be “on the grid”.
BATTERY BOX KIT WITH 2 12V BATTERIES  | ABBT2
The GHOST CONTROLS

®

 Battery Box Kit powers up your gate opener system. It includes two 7 Amp 

hour 12V batteries in the box. Battery box kit gets mounted next to the control panel.

12 VOLT , 7 AMP HOUR GEL-CELL BATTERY  | AXBT
Batteries provide the primary power to the gate opener system and are installed within the larger gate 

control box when auto/marine batteries are not used.

PHOTO EYES  | AXPE
Adjustable photo eyes for your outdoor environment. We offer monitored and non-monitored versions.

PUSH-TO-OPEN GATE BRACKET KIT | AXPO
The Push-To-Open Bracket is required for any gate opener system that is installed when the installation causes 

the gates to swing out from the property.  Most gates are installed with the swing action into the property and do 

not require these brackets.

ACCESSORIES

GHOST CONTROLS

®

 genuine accessories are designed to provide complete control and superior convenience for you and your family with your 

automatic gate opener. These products are specifically engineered to easily integrate into your system and grant you access to additional capabili-

ties and control of your gate opener. All of these accessories are available from your local dealer and are backed by the same reliable warranty that 

your gate operator is designed to meet.

Содержание DTP1





































































Отзывы: