Chamberlain C455 Скачать руководство пользователя | Manualshive

Страница: 1 / 44

background image

TO WATCH VIDEOS GO TO:

tinyurl.com/lgh5x3h

Contents

Preparation ......................................2-5
Assembly .......................................6-10
Installation ..................................11-28
Install the Door Control ............21-22
Install the Protector System® ....23-26
Power

......................................27-28

Adjustments .................................29-31
MyQ® Smartphone Control .................32
Operation .....................................33-37
  Using your Garage Door Opener .....34
  To Open the Door Manually ...........34

Multi-Function

Control Panel ...........................35-36

Remote Control and

Keyless Entry ................................36

Homelink®

...................................36

To Erase the Memory .....................37
Maintenance .....................................38
Troubleshooting ...........................39-40
Accessories ........................................41
Warranty ...........................................42
Repair Parts .................................43-44

Owner’s Manual

C455

Chain Drive

Garage Door Opener

FOR RESIDENTIAL USE ONLY

PRE-PROGRAMMED REMOTE CONTROL

INCLUDED

www.chamberlain.com

www.mychamberlain.com

•  Please read this manual and the enclosed safety materials carefully!
•  Fasten the manual near the garage door after installation.
•  The door WILL NOT CLOSE unless the Protector System

®

is connected

and properly aligned.

• Periodic checks of the garage door opener are required to ensure

safe operation.

• The model number label is located on the front panel of your garage

door opener.

• This garage door opener is compatible with MyQ® and

S

b

2.0® accessories.

• DO NOT install on a one-piece door if using devices or features

providing unattended close. Unattended devices and features are

to be used ONLY with sectional doors.

Smart Garage Opener

1
2
3
...
»

Содержание C455













































Отзывы:

Нет отзывов

Похожие инструкции для C455

Бренд: raumplus Страницы: 11

Бренд: Chamberlain Страницы: 12

Бренд: FAAC Страницы: 8

Бренд: FAAC Страницы: 12

Бренд: GBD Страницы: 8

Bart 350-24 Vcc

Бренд: fadini Страницы: 28

Бренд: Avidsen Страницы: 56

Бренд: RIB Страницы: 48

Бренд: CAME Страницы: 64

Бренд: Cardin Elettronica Страницы: 44

Бренд: Cardin Страницы: 52

Бренд: Cardale Страницы: 6

Бренд: Roma Страницы: 40

Бренд: PDS Страницы: 5

Бренд: SEA Страницы: 12

Бренд: SEA Страницы: 14

Бренд: V2 Страницы: 29

Бренд: EasyWay Страницы: 157

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды