Chamberlain C455 Скачать руководство пользователя | Manualshive

Страница: 20 / 44

background image

20

Installation

STEP 9 Connect the door arm to the trolley (continued)
OPTION B

ONE-PIECE DOORS

IMPORTANT:

The groove on the straight door arm MUST face away from the curved door arm.

1. Close the door. Disconnect the trolley by pulling the emergency release handle.
2. Fasten the straight door arm and the curved door arm together to the longest possible length

(with a 2 or 3 hole overlap) using the bolts, nuts, and lock washers.

3. Attach the straight door arm to the door bracket using the clevis pin. Secure with the ring

fastener.

4. Attach the curved door arm to the trolley using the clevis pin. Secure with the ring fastener.
5. Pull the emergency release handle toward the garage door opener until the trolley release

arm is horizontal.

HARDWARE

Hex Bolt 5/16"-18x7/8"

Nut 5/16"-18

Lock Washer
5/16" -18

Clevis Pin 5/16"x1"

Clevis Pin 5/16"x1-1/4"

Ring Fastener

One-Piece Door without Track

One-Piece Door with Track

Ring Fastener

Ring Fastener

Ring Fastener

Nut

Nut

Ring Fastener

Lock Washer

Lock Washer

Clevis Pin 5/16"x1-1/4"

Clevis Pin
5/16"x1-1/4"

Hex Bolts

Hex Bolts

Clevis Pin
5/16"x1"

Clevis Pin
5/16"x1"

Straight Door Arm

(Groove facing out)

Curved Door Arm

«
...
18
19
20
21
22
...
»

Содержание C455













































Отзывы:

Нет отзывов

Похожие инструкции для C455

Бренд: FAAC Страницы: 6

Бренд: CAME Страницы: 14

Бренд: CAME Страницы: 32

Бренд: Gartentorschliesser.com Страницы: 20

VIPER LED VIP10

Бренд: Key Automation Страницы: 116

Бренд: Byan System Страницы: 30

Бренд: tau Страницы: 40

GDO-9v2 SecuraLift

Бренд: Automatic Technology Страницы: 36

Бренд: Rival Страницы: 12

Бренд: Chamberlain Страницы: 92

Бренд: FAAC Страницы: 32

Бренд: CAME Страницы: 20

Бренд: Reporter Страницы: 7

Бренд: Platinum Access Systems Страницы: 33

Бренд: CAME Страницы: 12

Бренд: Chamberlain Страницы: 24

Бренд: CAME Страницы: 12

Бренд: Motorisation+ Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды