Chamberlain C455 Скачать руководство пользователя

Страница: 41 / 44

Accessories

Remote Control:

Works with ALL Chamberlain
openers from 1993-present.
MyQ

compatible. Includes

visor clip.

CLLP1

Laser Parking Assistant:

Park in the right spot every
time! A laser beam is activated
by your garage door opener
and projected on to the
dashboard of your vehicle to
guide perfect parking.

956EV

Keychain Remote Control:

Works with ALL Chamberlain
openers from 1993-present.
MyQ

compatible. With key

ring.

940EV

Wireless Keypad:

For use outside of the home
to enable access to the garage
using a 4-digit PIN. Works
with ALL Chamberlain openers
from 1993-present. MyQ

compatible.

Extension Brackets:

(Optional) For safety
reversing sensor installation
onto the wall or ﬂ oor.

CLOSED

OPEN

041A5281-1

6610CD

10 Foot (3 m) Rail
Extension:

To allow a 10 foot (3 m)
door to open fully.

8 Foot (2.4 m) Rail
Extension:

To allow an 8 foot (2.4 m)
door to open fully.

6608CD

MyQ

Accessories

PILCEV

MyQ

Remote Lamp Control:

Monitor and control this plug
in lamp switch with the MyQ

Smartphone App.

WSLCEV

MyQ

Interior/Exterior Light

Switch

Monitor and control this wall
light switch with the MyQ

Smartphone App.

CIGBU

MyQ

Internet Gateway:

Offers longer range wireless
signal than standard Wi-Fi.
Plugs into your home router
as an optional way to provide
MyQ

Smartphone Control for

your garage door opener and
MyQ

light controls.

953EV

Содержание C455













































Результаты поиска

Содержание C455

Отзывы:

Похожие инструкции для C455

Бренды по названию

Популярные бренды

Chamberlain C455, Руководство пользователя

Результаты поиска

Содержание C455

Отзывы:

Похожие инструкции для C455

Бренды по названию

Популярные бренды