Ghost Controls DTP1 страница 52 Скачать руководство пользователя | Manualshive

Страница: 52 / 68

background image

52

P U S H - T O - O P E N

© G h o s t C o n t r o l s 2 0 1 8

STEP 12. The arm has an internal limit switch that is fixed and is not adjustable. The arm when in the

fully retracted position will determine the

CLOSED position of the gate.

Use the remote transmitter to fully retract the arm. The arm will stop on its own.

ARM FULLY

RETRACTED

TURN THE CONTROL BOX OFF

STEP 13. Attach front mount bracket to the operator. The gate must remain in the desired closed

position.

CLOSE THE GATE TO THE DESIRED CLOSED POSITION

A. Temporarily assemble the front mount of the gate by inserting the supplied 10mm x 40mm clevis pin, 10mm

I.D. nylon spacer, and clevis hairpin through the gate bracket.

NOTE

ALTERNATE TUBE GATE BRACKETS FOR MOUNTING TUBULAR GATES. (NOT FOR USE WITH FLAT PANEL

GATES) see below image. Tube brackets (AXTB) sold separately.

«
...
50
51
52
53
54
...
»

Содержание DTP1





































































Отзывы:

Нет отзывов

Похожие инструкции для DTP1

Бренд: Vector Страницы: 54

Бренд: Vector2 Страницы: 52

2-IN-1 SAFETY CAN OPENER

Бренд: Lantana Страницы: 2

Бренд: SEA Страницы: 20

Black & Decker Can Opener JW200

Бренд: Black & Decker Страницы: 7

Бренд: V2 Страницы: 148

Бренд: CAME Страницы: 28

Бренд: GDS Страницы: 9

GDS 550P Series

Бренд: GDS Страницы: 15

Бренд: GDS Страницы: 17

Бренд: GDS Страницы: 17

Бренд: SOMFY Страницы: 18

Dexxo Optimo RTS

Бренд: SOMFY Страницы: 58

Бренд: Polaris Страницы: 187

Бренд: G.S.M Activate Страницы: 6

Бренд: FAAC Страницы: 16

Бренд: Beninca Страницы: 14

Estate Slide E-SL 1200 Series

Бренд: FAAC Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды