GEZE IO 420 Скачать руководство пользователя страница 8

  

GEZE IO 420

GEZE IO 420

15

 

 

14

5.4   Module type “4 doors”

The “4 doors” module type can be used for controlling four mutually independent doors. Only the connection of 

door contacts to the inputs is possible. The connection of a lock feedback or a release switch is not designated for 

this module type.

Connections

Assignment/function description

Input

1

Door contact door #1

2

Door contact door #2

3

Door contact door #3

4

Door contact door #4

Output

1

Electric strike fail safe door #1

2

Electric strike fail safe door #2

3

Electric strike fail safe door #3

4

Electric strike fail safe door #4

Tab. 4: Pin assignment module type “4-doors”

current state – current state

State changes to

State changes with

unlocked 

In this state output 1, 2, 3 or 4 is enabled. 

locked 

if time switch is not enabled.

 

à

CAN command “lock”

 

à

BACnet command “lock”

 

à

sabotage

time switch (ZSU)

If ZSU is active and one of the above-men-

tioned release devices occurs.

locked 

In this state output 1, 2, 3 or 4 is disabled. 

unlocked

 

à

CAN command “unlock”

 

à

BACnet command “unlock” 

short-term release (KZF)

 

à

CAN command “short-term release”

 

à

BACnet command “short-term release”

time switch (ZSU)

If ZSU message is enabled and if ZSU was 

not interrupted.

short-term release (KZF) 

In this state output 1, 2, 3 or 4 is enabled. 

KZF re-triggering is not possible in this 

mode. 

locked

if KZF time has expired

if KZF interruptible is enabled and the door 

is closed again after opening. The min. KZF 

time is 2.5 seconds.

unlocked

 

à

CAN command “unlock”

 

à

BACnet command “unlock”

time switch (ZSU) 

In this state output 1, 2, 3 or 4 is enabled. 

locked 

with enabled option time switch interrup-

tion

 

à

CAN command “lock”.

 

à

BACnet command “lock”

locked 

without enabled option time switch inter-

ruption

 

à

sabotage 

 

à

If time switch message is no longer 

enabled.

5.5   Module type “automatic stat” / “automatic 4 sec”

With this module type, the IO 420 can control a GEZE door drive via inputs/outputs. Switches can be connected at 

input 1 and 2 for this. Input 3 and 4 are used to evaluate the door feedback.

With this module type, no fault messages of the drive can be evaluated via the IO 420, since the drive communicates 

via the inputs/outputs rather than via RS485.

Connections

Assignment/function description

Input

1

 

à

rising flank:

 change of state to “automatic” 

 

à

falling flank:

 change of state to “night”

2

 

à

rising flank: 

change of state to “permanently open”

 

à

falling flank: 

no effect

3

Lock state

4

Door contact

Output

1

Command to DCU “night”

2

Command to DCU “shop closed”

3

Command to DCU “automatic”

4

Command to DCU “permanently open”

Tab. 5: Pin assignment of module type “automatic”

State

State changes to

State changes with

automatic 

Output 3 is enabled.  

If module type “automatic 4 sec” is enabled, 

output 3 is switched off again after 4 

seconds. 

night

 

à

falling flank input 1

 

à

CAN command “night”

 

à

BACnet command “night”

shop closed

 

à

CAN command “close shop”

 

à

BACnet command “close shop”

permanently open

 

à

of the rising flank input 2

 

à

CAN command “permanent open”

 

à

BACnet command “permanent open”

shop closed (exit only) 

Output 2 is enabled. If module type “auto-

matic 4 sec” is enabled, output 2 is switched 

off again after 4 seconds.

night

 

à

of the falling flank input 1

 

à

CAN command “night”

 

à

BACnet command “night”

automatic

 

à

of the rising flank input 1

 

à

CAN command “automatic”

 

à

BACnet command “automatic”

permanently open

 

à

of the rising flank input 2

 

à

CAN command “permanent open”

 

à

BACnet command “permanent open”

permanently open:  

Output 4 is enabled. If module type “auto-

matic 4 sec” is enabled, output 4 is switched 

off again after 4 seconds. 

night

 

à

of the falling flank input 1

 

à

CAN command “night”

 

à

BACnet command “night”

shop closed

 

à

CAN command “close shop”

 

à

BACnet command “close shop”

automatic

 

à

of the rising flank input 1

 

à

CAN command “automatic”

 

à

BACnet command “automatic”

night

Output 1 is enabled. If module type “auto-

matic 4 sec” is enabled, output 1 is switched 

off again after 4 seconds. 

automatic

 

à

of the rising flank input 1

 

à

CAN command “automatic”

 

à

BACnet command “automatic”

shop closed

 

à

CAN command “close shop” 

 

à

BACnet command “close shop”

permanently open

 

à

of the rising flank input 2

 

à

CAN command “permanent open”

 

à

BACnet command “permanent open”

GEZE IO 420

5

 

3.2.1  LEDs

LED 1

 - (rot)

LED blinkt, wenn microSD-Card gelesen oder geschrieben wird.

 

LED 2

 - (gelb)

LED leuchtet, wenn „CP“ (Kondensatorplatine) angeschlossen ist.

LED 3

 - (rot)

LED blinkt bei Störung.

LED 4

 - (grün)

LED blinkt im normalen Betrieb.

LED 5

 - (grün)

LED leuchtet, wenn Spannungsversorgung für Microcontroller aktiv ist.

LED 6

 - (gelb)

LED blinkt, wenn Daten über BACnet ausgetauscht werden.

LED in

 - (grün)

LED-in 4/3/2/1 leuchtet, wenn Eingang “in” 4/3/2/1 aktiv ist.

LED out

 - (rot)

LED-out 4/3/2/1 leuchtet, wenn Ausgang “out” 4/3/2/1 aktiv ist.

3.2.2  Schnittstellen / GEZE IO 420

Schnittstellen

 

à

CAN: 

50 kBit/s, verwendet für TE 200, VAT 220, TZ 320.

 

à

ST 220: 

verwendet für ST 220, IQ-Aut Standflügel.

 

à

GEZE-Bus: 

verwendet für IQ-Aut Gangflügel.

 

à

BACnet: 

verwendet für BACnet MS/TP-Schnittstelle. 

3.2.3  DIP-Schalter Konfiguration

CAN:

Abschlusswiderstand „CAN“ 120 Ohm

 

X

DIP-Schalter am Anfang und Ende des CAN-BUS auf ON setzen.

BACnet:

Abschlusswiderstand „BACnet“ 

120 Ohm

 

X

BACnet DIP-Schalter am ersten und am letzen IO 420 des BACnet MS/TP Bus auf ON setzen.

GEZE-Bus:

DIP-Schalter Abschlusswiderstand „GEZE-Bus“ 120 Ohm

 

X

Bei Anschluss von GEZE-Motorschloss oder TZ 320 (Anschluss für KL 220), DIP-Schalter auf 

ON setzen.

Network-Bias:

DIP-Schalter „Network-Bias“ 

 

X

Um den Network-Bias für BACnet MS/TP zu aktivieren, DIP-Schalter auf ON setzen. 

In einem BACnet MS/TP Netwerksystem darf nur ein Bias aktiviert sein.

3.2.4  microSD

microSD-Card

Die microSD-Card (SDHC) wird im FAT16/32-Fileformat geschrieben und gelesen. Andere Formate 

werden nicht unterstützt. Die Dateien des IO 420 können auf eine microSD-Card kopiert werden. 

Hierfür wird das ST 220 benötigt. Gegebenenfalls können die Daten am PC weiter angepasst werden 

(Parametrierung oder Änderung der BACnet-Namen). Das Profil kann dann mittels microSD-Card auf 

ein anderes IO 420 mit gleicher Firmware geladen werden. 

Folgende Dateien werden auf der Karte erstellt:

 

à

Namensdatei für BACnet-Namen: 

„IO420_V1.BAC“;

 

 

à

Konfigurationsdatei: 

„IO420_V1.CON“

; beinhaltet alle Parameter des IO 420.

 

à

Log-Datei: 

„IO420_00.LOG“

 bis 

„IO420_39.LOG“

Je nach Einstellung werden Alarmmeldungen und Aktionen in die Log-Datei geschrieben.

     

Wenn die LED für microSD-Card blinkt, darf die microSD-Card nicht aus dem Slot herausgenommen werden.  

Zum Entfernen und Einstecken der microSD-Card das IO 420 spannungslos schalten. 

3.2.5  Reset 

Reset-Taster

Mit dem Reset-Taster kann die Werkseinstellung wiederhergestellt werden.  

Reset durchführen

 

X

Gerät spannungslos schalten.

 

X

„Reset-Button“ auf der Platine gedrückt halten.

 

X

Spannungsversorgung einschalten. 

Nach 6 Sekunden wird das Gerät auf Werkseinstellung versetzt.  

LED 3 „Störung“ und LED 4 „Normalbetrieb“ blinken im 0,4 Sekunden-Takt gleichzeitig. 

 

X

Wenn die LEDs blinken „Reset-Button“ loslassen.

 

X

Um das Gerät in den Betriebsmodus zurückzusetzen, Spannungsversorgung aus- und wieder 

einschalten.

 

Содержание IO 420






















Отзывы: