GEZE FA GC 150 Скачать руководство пользователя страница 39

Страница: 39 / 60

GEZE hold-open system FA GC 150

Wiring diagram

5.5.3 Contact of the fire alarm system and manual trigger switch UTA

The general construction technique permit requires line monitoring to the potential-free contact of the fire

alarm system and to the manual trigger switch.

Line monitoring is active if:

a 2.2 kΩ resistor is connected in parallel at the end of the cable.

Connect the potential-free contact as a normally open contact

Potentialfreier Kontakt (BMA)

2,2 k

GC 175

UTA

Fig. 5.5.3.1

The cable to the potential-free contact (fire-alarm system) must be laid separately or protected.

5.6 Alarm output

Potential-free relay output, changer, maximum 24 V, 1 A

In normal operation the contact 11-12 is open, in the event of power failure or alarm closed.

Do not supply alarm display from the hold-open system.

24 V external

Alarm

display

GND external

Fig. 5.6.1

5.7 Mutual triggering of two hold-open systems

Two hold-open systems can trigger each other mutually. For this purpose, the alarm contact of the one lintel-

mounted smoke switch is connected with the input MRB of the other lintel-mounted smoke switch.

If additional manual trigger switches are required, these are connected in parallel to the connection at the

respective input MRB.

Remove jumper J1 from both lintel-mounted smoke switches.

The general construction technique permit requires monitoring of the lines between the two lintel-mounted

smoke switches.

Line monitoring is active if:

jumper J3 of the two lintel-mounted smoke switches to the measuring chamber is set (2-3, see chap. 4.4),

a 43 kΩ resistor is connected in parallel at both lintel-mounted smoke switches directly at the alarm output.

German

institute for

construction

technology

Potential-free contact (BMA)

German

institute for

construction

technology

Содержание FA GC 150





























































Результаты поиска

Содержание FA GC 150

Отзывы:

Похожие инструкции для FA GC 150

Бренды по названию

Популярные бренды

GEZE FA GC 150, Инструкция по установке

Результаты поиска

Содержание FA GC 150

Отзывы:

Похожие инструкции для FA GC 150

Бренды по названию

Популярные бренды