GEZE FA GC 150 Скачать руководство пользователя страница 13

Страница: 13 / 60

GEZE hold-open system FA GC 150

Technical data

4.4 Lintel-mounted smoke switch GC 151

Lintel-mounted smoke switch GC 151

ID 142250

Functional principle

Scatter light, adaption of the alarm threshold, no alarm saving (self-

resetting as soon as there is no longer any smoke in the measuring

chamber)

Input voltage

24 V ± 0,5 V DC

Input current

maximum 15 mA

Installation position

Wall (lintel) installation, horizontal

Output hold-open device

Transistor output, short-circuit proof

Free-wheeling diode for inductive load, maximum 24 V, 200 mA

in the event of an alarm switch-off of the hold-open device for at least 4 s

Additional detectors

Connection of up to 3 ceiling-mounted detectors using 3-line technology

Line monitoring (can be switched off) using two terminating resistors

(43 kΩ each) at the end of the cable

Manual trigger switch

Line monitoring (can be switched off) using terminating resistor

(43 kΩ) at the end of the cable

Alarm output

Potential-free relay output, changer

maximum 24 V DC / maximum 1 A

Test button

The hold-open device is switched off as long as the key is pressed

(for at least 4 s)

Reset of the smoke switch by activating the button

Detector test

Alarm triggering: with test button or with test aerosol

Line monitoring may only be deactivated when used as a spare part in old systems without line monitoring

(ORS 141).

Switch the supply voltage off before changing the jumper setting (remove terminal clamp KL1).

The new jumper setting only becomes active after the mains voltage has been switched back on again.

Power supply

External hold-open

mechanism

Manual trigger

switch

Ceiling-mounted

detector

Alarm output

Measuring chamber

Internal hold-open

mechanism

without manual trigger switch

with manual trigger switch

without

ceiling-mounted detector

with

ceiling-mounted detector

without line monitoring

to the manual trigger switch

and/or ceiling-mounted detector

with line monitoring

to the manual trigger switch

and/or ceiling-mounted detector

Test button

LED for state

and fault display

Jumper set

Jumper not set

Fig. 4.4.1

Содержание FA GC 150





























































Результаты поиска

Содержание FA GC 150

Отзывы:

Похожие инструкции для FA GC 150

Бренды по названию

Популярные бренды

GEZE FA GC 150, Инструкция по установке

Результаты поиска

Содержание FA GC 150

Отзывы:

Похожие инструкции для FA GC 150

Бренды по названию

Популярные бренды