Gewiss CHORUS GWA9531 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 57

background image

12

4

LIGHT OUTPUT SETTING

4.1 Basic settings

During project configuration, it is advisable first to set parameters for mode (full automatic,
semi-automatic, slave or occupancy-independent regulation) and output type (switching or
regulation). Output type affects the output object. In switching mode, a 1-bit object (15:
Switching channel

– Output) is used, and in regulating mode a 1-byte object (16: Value 1 –

Output).

After that, it is recommended that you define the brightness threshold or set value and the
follow-up time. Following these basic settings, the detector is ready for service. All other
settings/parameters are for optimization or for adjustment in particular situations.

«
...
10
11
12
13
14
...
»

Содержание CHORUS GWA9531


























































Отзывы:

Нет отзывов

Похожие инструкции для CHORUS GWA9531

Бренд: CAB Страницы: 10

Бренд: Canon Страницы: 14

IMAGE STABILIZER EF70-200MM F/4L IS USM

Бренд: Canon Страницы: 13

TIMER REMOTE CONTROLLER TC-80N3

Бренд: Canon Страницы: 3

TIMER REMOTE CONTROLLER TC-80N3

Бренд: Canon Страницы: 2

EF-S55-250mm f/4-5.6 IS II

Бренд: Canon Страницы: 7

Бренд: K&M Страницы: 9

Бренд: Panasonic Страницы: 2

Бренд: Quincy lab Страницы: 4

DWSC - Vintage C

Бренд: Daikin Страницы: 57

Бренд: Sanitas Страницы: 52

Бренд: UltraGauge Страницы: 55

Бренд: NavLinkz Страницы: 4

ShowMatch DeltaQ SMGSB

Бренд: Bose Страницы: 2

Бренд: Klarstein Страницы: 24

Бренд: SpectraLink Страницы: 14

Бренд: EUFAB Страницы: 52

Бренд: GDC Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды