Gewiss CHORUS GWA9531 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 57

background image

50

The standard format of the object is

1 byte

and the information it contains is “VALUE

%”



Output- Value 2 (n.17)

This object is used to send value 2 %
The enabled flags are C (communication), R (read by bus) and T (Trasmission).
The standard format of the object is 5.001 DPT_Scaling.
The standard format of the object is

1 byte and the information it contains is

“VALUE

%”



Output- Current threshold (n.18)

This object is used to send the current threshold.
The enabled flags are C (communication), R (read by bus) and T (Trasmission).
The standard format of the object is

1 bit



Output- Burn-in time status (n.19)

This object is used to receive from the bus the Burn-in time missing.
The enabled flags are C (communication), R (read by bus) and T (Trasmission).
The standard format of the object is 7.006 DPT_TimePeriodMin.
The standard format of the object is

2 byte and the information it contains is

”VALUE

(min)”



Input- Locking object (n.20)

This object is used to block the HVAC 1 channel.

The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 1.010 DPT_Switch.
The standard format of the object is

1 bit and the information it contains is

“Start/Stop”.



Input- External influence (n.21)

This object is used to receive external control of the HVAC 1 channel.

The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 1.001 DPT_Switch.
The standard format of the object is

1 bit and the information it contains is

“On/Off”.



Input- Follow-up time in minutes (n.22)

This object is used to set follow time on HVAC 1 channel.
The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 7.006 DPT_TimePeriodMin.
The standard format of the object is

2 byte and the information it contains is

”VALUE

(min)”



Input- Overwrite threshold (n.23)

This object is used to overwrite threshold on HVAC 1 channel.

The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 9.004 DPT_Value_Lux.
The standard format of the object is

2 byte and the information it contains is

“Value_Lux”.

«
...
48
49
50
51
52
...
»

Содержание CHORUS GWA9531


























































Отзывы:

Нет отзывов

Похожие инструкции для CHORUS GWA9531

Бренд: Zell Страницы: 33

Бренд: Canon Страницы: 14

IMAGE STABILIZER EF70-200MM F/4L IS USM

Бренд: Canon Страницы: 13

TIMER REMOTE CONTROLLER TC-80N3

Бренд: Canon Страницы: 3

TIMER REMOTE CONTROLLER TC-80N3

Бренд: Canon Страницы: 2

EF-S55-250mm f/4-5.6 IS II

Бренд: Canon Страницы: 7

Бренд: Calumet Страницы: 4

Бренд: Campbell Страницы: 70

Бренд: Yuasa Страницы: 35

Бренд: 3M Страницы: 10

Бренд: Obelink Страницы: 2

Бренд: Panasonic Страницы: 4

Бренд: Daikin Страницы: 52

Бренд: Bamo Страницы: 4

Бренд: DEFA Страницы: 9

Slim Line LED Light Grille Kit

Бренд: rough country Страницы: 8

Alpha Top Easy-Flue 500 mm

Бренд: Alpha Страницы: 6

signal mirror 2005-2009 Ford Mustang

Бренд: muth Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды